數模A/D和模數D/A轉換的基本應用（下）

代碼相關：

/**********Lcd1602.c**************/
#include < reg52.h >
#define LCD1602_DB  P2
sbit LCD1602_RS = P0^3;
sbit LCD1602_RW = P0^2;
sbit LCD1602_E  = P0^1;
void LcdWaitReady()
{
    unsigned char sta;  
    LCD1602_DB = 0xFF;
    LCD1602_RS = 0;
    LCD1602_RW = 1;
    do {
        LCD1602_E = 1;
        sta = LCD1602_DB; //讀取狀態字
        LCD1602_E = 0;
    } while (sta & 0x80); //bit7等于1表示液晶正忙，重復檢測直到其等于0為止
}
/* 向LCD1602液晶寫入一字節命令，cmd-待寫入命令值 */
void LcdWriteCmd(unsigned char cmd)
{
    LcdWaitReady();
    LCD1602_RS = 0;
    LCD1602_RW = 0;
    LCD1602_DB = cmd;
    LCD1602_E  = 1;
    LCD1602_E  = 0;
}
/* 向LCD1602液晶寫入一字節數據，dat-待寫入數據值 */
void LcdWriteDat(unsigned char dat)
{
    LcdWaitReady();
    LCD1602_RS = 1;
    LCD1602_RW = 0;
    LCD1602_DB = dat;
    LCD1602_E  = 1;
    LCD1602_E  = 0;
}
void LcdSetCursor(unsigned char x, unsigned char y)
{
    unsigned char addr;

    if (y == 0)  //由輸入的屏幕坐標計算顯示RAM的地址
        addr = 0x00 + x;  //第一行字符地址從0x00起始
    else
        addr = 0x40 + x;  //第二行字符地址從0x40起始
    LcdWriteCmd(addr | 0x80);  //設置RAM地址
}


void LcdShowStr(unsigned char x, unsigned char y, unsigned char *str)
{
    LcdSetCursor(x, y);   //設置起始地址
    while (*str != '?')  //連續寫入字符串數據，直到檢測到結束符
    {
        LcdWriteDat(*str++);
    }
}
/* 初始化1602液晶 */
void InitLcd1602()
{
    LcdWriteCmd(0x38);  
    LcdWriteCmd(0x0C);  
    LcdWriteCmd(0x06);  
    LcdWriteCmd(0x01);  
}

/*********************IIC*******************/
#include < reg52.h >
#include < intrins.h >
#define Delay()  {_nop_();_nop_();_nop_();_nop_();_nop_();}
sbit I2C_SCL = P3^7;
sbit I2C_SDA = P3^6;


/* 起始信號 */
void I2CStart()
{
    I2C_SDA = 1; 
    I2C_SCL = 1;
    Delay();
    I2C_SDA = 0; 
    Delay();
    I2C_SCL = 0; 
}
/* 停止信號 */
void I2CStop()
{
    I2C_SCL = 0; //首先確保SDA、SCL都是低電平
    I2C_SDA = 0;
    Delay();
    I2C_SCL = 1; //先拉高SCL
    Delay();
    I2C_SDA = 1; //再拉高SDA
    Delay();
}
/* I2C總線寫操作，dat-待寫入字節，返回值-從機應答位的值 */
bit I2CWrite(unsigned char dat)
{
    bit ack;  
    unsigned char BitCnt;  


    for (BitCnt=0x80; BitCnt!=0; BitCnt >?>=1) 
    {
        if ((BitCnt&dat) == 0)  
            I2C_SDA = 0;
        else
            I2C_SDA = 1;
        Delay();
        I2C_SCL = 1;          //拉高SCL
        Delay();
        I2C_SCL = 0;          //再拉低SCL，完成一個位周期
    }
    I2C_SDA = 1;  
    Delay();
    I2C_SCL = 1;   
    ack = I2C_SDA; 
    Delay();
    I2C_SCL = 0; 


    return (ack); 

}


/* I2C總線讀操作，并發送應答信號或者非應答信號，如果cnt為1則發送應答信號，
如果cnt為非1的值則發送非應答信號，返回值-讀到的字節 */
unsigned char I2CReadACKORNOT(bit cnt)
{
    unsigned char BitCnt;
    unsigned char dat;


    I2C_SDA = 1;  //首先確保主機釋放SDA
    for (BitCnt=0x80; BitCnt!=0; BitCnt >?>=1) //從高位到低位依次進行
    {
        Delay();
        I2C_SCL = 1;      //拉高SCL
        if(I2C_SDA == 0)  //讀取SDA的值
            dat &= ~BitCnt; //為0時，dat中對應位清零
        else
            dat |= BitCnt;  //為1時，dat中對應位置1
        Delay();
        I2C_SCL = 0;      //再拉低SCL，以使從機發送出下一位
    }
    if(cnt)
    I2C_SDA = 0;   //8位數據發送完后，拉低SDA，發送應答信號
    else
    I2C_SDA = 1;
  Delay();
    I2C_SCL = 1;   //拉高SCL
    Delay();
    I2C_SCL = 0;   //再拉低SCL完成應答位，并保持住總線


    return dat;
}

/******************main.c*************************/
#include < reg52.h >
bit flags = 1;  
unsigned char GetValue(unsigned char chn);
void NumToString(unsigned char *str, unsigned char val);
extern void I2CStart();
extern void I2CStop();
unsigned char I2CReadACKORNOT(bit cnt);
extern bit I2CWrite(unsigned char dat);
extern void InitLcd1602();
extern void LcdShowStr(unsigned char x, unsigned char y, unsigned char *str);


void main()
{
    unsigned char val;
    unsigned char str[10];

    EA = 1;            //開總中斷
    TMOD &= 0xF0;   //清零T0的控制位
    TMOD |= 0x01;   //配置T0為模式1
    TH0 = (65536-9216)/256;     //加載T0重載值,定時10ms
    TL0 = (65536-9216)%256;
    ET0 = 1;        //使能T0中斷
    TR0 = 1;        //啟動T0
    InitLcd1602();     //初始化液晶    
    LcdShowStr(0, 0, "AN0:  AN1:  AN3:");  //顯示通道指示

    while (1)
    {
        if (flags)
        {
            flags = 0;
            //顯示通道0的電壓
            val = GetValue(0);     //獲取ADC通道0的轉換值
            NumToString(str, val);  //轉為字符串格式的電壓值
            LcdShowStr(0, 1, str);    //顯示到液晶上
            //顯示通道1的電壓
            val = GetValue(1);
            NumToString(str, val);
            LcdShowStr(6, 1, str);
            //顯示通道3的電壓
            val = GetValue(3);
            NumToString(str, val);
            LcdShowStr(12, 1, str);
        }
    }
}
unsigned char GetValue(unsigned char chn)
{
  unsigned char val;


  I2CStart();
  if(I2CWrite(0x48< 1))
  {
    I2CStop();
    return 0;
  }
  I2CWrite(0x40 | chn);
  I2CStart();
  I2CWrite(0x48< 1 | 0x01);
  I2CReadACKORNOT(1);
  val = I2CReadACKORNOT(0);
  I2CStop();
  return val;
}


void  NumToString(unsigned char *str, unsigned char val)
{
  val = (val*50)/255;
  str[0] = (val/10) + '0';
  str[1] = '.';
  str[2] = (val%10) + '0';
  str[3] = '?';

}


/* T0中斷服務函數 */
void InterruptTimer0() interrupt 1
{
    static unsigned char tm100ms = 0;

    TH0 = (65536-9216)/256;     //加載T0重載值
    TL0 = (65536-9216)%256;
    tm100ms++;
    if (tm100ms >= 10)  //定時100ms
    {
        tm100ms = 0;
        flags = 1;
    }
}

AN3通道測得實際電壓變化，通過滑動變阻器可以改變相應的值;AN0通道測得光敏電阻的阻值；AN1測得熱敏電阻的相應阻值，需要貨源才會變化值。