產生的代碼 - 如何使用STATECAD進行多狀態(tài)機設計實例分析

由以上的波形看到狀態(tài)機的工作過程符合設計邏輯。對單獨的器件操作也許不需要采用多狀態(tài)機的設計方法，但在多器件需要并行工作時，多狀態(tài)機的協同設計就顯得必要了。導出VHDL模型塊到ISE中進行仿真后綜合,這里就不多講了，以下是產生的代碼：

　　-- D:XILINXTUTORIALDUOZTJI.Vhd

　　LIBRARY Ieee;

　　USE Ieee.Std_logic_1164.All;

　　LIBRARY Ieee;

　　USE Ieee.Std_logic_unsigned.All;

　　ENTITY SHELL_DUOZTJI IS

　　PORT (CLK,RESET: IN Std_logic;

　　Dcounter0,Dcounter1 : OUT Std_logic);

　　SIGNAL BP_dcounter0,BP_dcounter1,Readcounter0,Readcounter1: Std_logic;

　　END;

　　ARCHITECTURE BEHAVIOR OF SHELL_DUOZTJI IS

　　SIGNAL Sreg : Std_logic_vector (1 DOWNTO 0);

　　SIGNAL Next_sreg : Std_logic_vector (1 DOWNTO 0);

　　CONSTANT M0full : Std_logic_vector (1 DOWNTO 0) :="00";

　　CONSTANT M0writewait : Std_logic_vector (1 DOWNTO 0) :="01";

　　CONSTANT STATE0 : Std_logic_vector (1 DOWNTO 0) :="10";

　　CONSTANT Write0 : Std_logic_vector (1 DOWNTO 0) :="11";

　　SIGNAL Sreg1 : Std_logic_vector (1 DOWNTO 0);

　　SIGNAL Next_sreg1 : Std_logic_vector (1 DOWNTO 0);

　　CONSTANT M0empty : Std_logic_vector (1 DOWNTO 0) :="00";

　　CONSTANT M0readwait : Std_logic_vector (1 DOWNTO 0) :="01";

　　CONSTANT Read0 : Std_logic_vector (1 DOWNTO 0) :="10";

　　CONSTANT STATE1 : Std_logic_vector (1 DOWNTO 0) :="11";

　　SIGNAL Next_BP_dcounter0,Next_BP_dcounter1,Next_readcounter0,

　　Next_readcounter1 : Std_logic;

　　SIGNAL BP_dcounter : Std_logic_vector (1 DOWNTO 0);

　　SIGNAL Dcounter : Std_logic_vector (1 DOWNTO 0);

　　SIGNAL Readcounter : Std_logic_vector (1 DOWNTO 0);

　　BEGIN

　　PROCESS (CLK, Next_sreg, Next_BP_dcounter1, Next_BP_dcounter0)

　　BEGIN

　　IF CLK=''1'' AND CLK''Event THEN

　　Sreg <= Next_sreg;

　　BP_dcounter1 <= Next_BP_dcounter1;

　　BP_dcounter0 <= Next_BP_dcounter0;

　　END IF;

　　END PROCESS;

　　PROCESS (CLK, Next_sreg1, Next_readcounter1, Next_readcounter0)

　　BEGIN

　　IF CLK=''1'' AND CLK''Event THEN

　　Sreg1 <= Next_sreg1;

　　Readcounter1 <= Next_readcounter1;

　　Readcounter0 <= Next_readcounter0;

　　END IF;

　　END PROCESS;

　　PROCESS (Sreg,Sreg1,BP_dcounter0,BP_dcounter1,Readcounter0,Readcounter1,

　　RESET,BP_dcounter,Readcounter)

　　BEGIN

　　Next_BP_dcounter0 <= BP_dcounter0;Next_BP_dcounter1 <= BP_dcounter1;

　　Next_readcounter0 <= Readcounter0;Next_readcounter1 <= Readcounter1;

　　BP_dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)));

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)));

　　Next_sreg<=M0full;

　　Next_sreg1<=M0empty;

　　IF ( RESET=''1'' ) THEN

　　Next_sreg<=STATE0;

　　BP_dcounter <= (Std_logic_vector''("00"));

　　ELSE

　　CASE Sreg IS

　　WHEN M0full =>

　　Next_sreg<=M0writewait;

　　BP_dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)));

　　WHEN M0writewait =>

　　IF ( (Sreg1=M0empty)) THEN

　　Next_sreg<=Write0;

　　BP_dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)) + Std_logic_vector''("01"));

　　ELSE

　　Next_sreg<=M0writewait;

　　BP_dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)));

　　END IF;

　　WHEN STATE0 =>

　　Next_sreg<=Write0;

　　BP_dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)) +

　　Std_logic_vector''("01"));

　　WHEN Write0 =>

　　IF ( BP_dcounter0=''1'' AND BP_dcounter1=''1'' ) THEN

　　Next_sreg<=M0full;

　　BP_dcounter <= (Std_logic_vector''("00"));

　　ELSE

　　Next_sreg<=Write0;

　　BP_dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)) +

　　Std_logic_vector''("01"));

　　END IF;

　　WHEN OTHERS =>

　　END CASE;

　　END IF;

　　IF ( RESET=''1'' ) THEN

　　Next_sreg1<=STATE1;

　　Readcounter <= (Std_logic_vector''("00"));

　　ELSE

　　CASE Sreg1 IS

　　WHEN M0empty =>

　　Next_sreg1<=M0readwait;

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)));

　　WHEN M0readwait =>

　　IF ( (Sreg=M0full)) THEN

　　Next_sreg1<=Read0;

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)) +

　　Std_logic_vector''("01"));

　　ELSE

　　Next_sreg1<=M0readwait;

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)));

　　END IF;

　　WHEN Read0 =>

　　IF ( Readcounter0=''1'' AND Readcounter1=''1'' ) THEN

　　Next_sreg1<=M0empty;

　　Readcounter <= (Std_logic_vector''("00"));

　　ELSE

　　Next_sreg1<=Read0;

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)) +

　　Std_logic_vector''("01"));

　　END IF;

　　WHEN STATE1 =>

　　IF ( (Sreg=M0full)) THEN

　　Next_sreg1<=Read0;

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)) + Std_logic_vector''("01"));

　　ELSE

　　Next_sreg1<=STATE1;

　　Readcounter <= (( Std_logic_vector''(Readcounter1, Readcounter0)));

　　END IF;

　　WHEN OTHERS =>

　　END CASE;

　　END IF;

　　Next_BP_dcounter1 <= BP_dcounter(1);

　　Next_BP_dcounter0 <= BP_dcounter(0);

　　Next_readcounter1 <= Readcounter(1);

　　Next_readcounter0 <= Readcounter(0);

　　END PROCESS;

　　PROCESS (BP_dcounter0,BP_dcounter1,Dcounter)

　　BEGIN

　　Dcounter <= (( Std_logic_vector''(BP_dcounter1, BP_dcounter0)));

　　Dcounter0 <= Dcounter(0);

　　Dcounter1 <= Dcounter(1);

　　END PROCESS;

　　END BEHAVIOR;

　　LIBRARY Ieee;

　　USE Ieee.Std_logic_1164.All;

　　LIBRARY Ieee;

　　USE Ieee.Std_logic_unsigned.All;

　　ENTITY DUOZTJI IS

　　PORT (Dcounter : OUT Std_logic_vector (1 DOWNTO 0);

　　CLK,RESET: IN Std_logic);

　　END;

　　ARCHITECTURE BEHAVIOR OF DUOZTJI IS

　　COMPONENT SHELL_DUOZTJI

　　PORT (CLK,RESET: IN Std_logic;

　　Dcounter0,Dcounter1 : OUT Std_logic);

　　END COMPONENT;

　　BEGIN

　　SHELL1_DUOZTJI : SHELL_DUOZTJI PORT MAP (CLK=>CLK,RESET=>RESET,Dcounter0=>

　　Dcounter(0),Dcounter1=>Dcounter(1));

　　END BEHAVIOR;