基于小凌派開發板的迪文屏控制案例

前言：因2個原因?qū)е逻t遲沒有出來想要的效果。原因1：迪文屏的中文字庫問題，對CFG文件及FLASH的分配不熟，導致icl文件覆蓋了字庫文件，在迪文論壇發帖解決。原因2：串口線不能2節連接，我測試一直2節杜邦線連接，導致rk2206發不出數據，用串口demo測試，只有一節杜邦線電腦才能接到數據，弄了一節將兩個板子連接終于可以了。

1

迪文屏方面

1、用dgus軟件設計的歡迎使用界面中生成0號字庫和GBK字庫，如圖1所示，點擊DGUS字庫，出現如圖2所示，生成0號ASCII字庫。

圖1 dgus字庫生成

圖2 生成0號字庫

2、下面就來生成GBK漢字庫，如圖3和圖4所示，生成的24宋體24.bin字庫。

圖3 GBK字庫

圖4 生成漢字庫gbk

3、接下來，新建GUI工程，選一張480*854的背景圖，如圖5所示，保存位置確定。

圖5 新建GUI工程

4、網上找了9張圖標，其中自己用位圖編輯了一遍，想多大自己設置即可，用DWIN ICL生成工具生成圖標icl，如圖6所示

圖6 生成圖標icl

圖7 導入生成

5、生成背景icl一樣。注意：軟件默認背景圖為32.icl，生成CFG文件時需要修改。這個根據屏的flash大小設置，我的屏只有8M，因此最大為30，32超出了出現了問題。

6、在背景圖上放置一個圖標控件和2個text控件，如圖8所示，text地址設置2000，另一個設置2064。設置TEXT的屬性，ASCII選擇0號字庫，漢字庫選24號字庫，編碼選擇GBK編碼，后面的X和Y點陣設置為24點陣。這個點陣數根據自己字庫生成的點陣設置。使用出廠的字庫，則分別為0號字庫和12漢字庫。配置為0和12即可。

圖8 放置顯示控件

圖9 text設置屬性

7、設置變量圖標顯示屬性，如圖10所示，從0開始到8共9個變量圖標。

圖10 變量圖標顯示設置

最后生成即可。

2

T5L51方面

1、因我刷過T5L51，所以串口2調試協議不通，只能重刷出廠程序或者自己寫程序。我自己寫的程序，在熊家余老師的串口程序基礎上寫自己的接收代碼，main函數如下代碼：

#include "sys.h"#include "uart2.h"#include "string.h"
#define FIRST_TXT  "手勢結果：" //必須以兩個字節的0x00或者兩個字節的0xFF為文本結束標記
void main(void){      u16 len;    s16 ges;    u8 text_buf[32]={0};    u16 ic_sta;//存儲ICON值    sys_init();//系統初始化        sys_write_vp(0x2000,FIRST_TXT,sizeof(FIRST_TXT)/2+1);//給第一個文本顯示控件設置文本內容        uart2_init(115200);//初始化串口2        while(1)    {          IF(uart2_rx_sta&UART2_PACKET_OK)//接受到了串口數據包        {            len = uart2_rx_sta&UART2_PACKET_LEN;//得到串口數據包的長度,不包含"
"或者'
'結束符的長度                        ges = uart2_buf[0]+uart2_buf[1]*256;            switch(ges)            {                case 1:                    ic_sta = 0;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_UP:0x%x",ges);                break;                case 2:                    ic_sta = 1;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_DOWN:0x%x",ges);                break;                case 4:                    ic_sta = 2;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                    sprintf(text_buf,"GES_LEFT:0x%x",ges);                break;                case 8:                    ic_sta = 3;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_RIGHT:0x%x",ges);                break;                case 16:                    ic_sta = 4;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_FORWARD:0x%x",ges);                break;                case 32:                    ic_sta = 5;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_BACKWARD:0x%x",ges);                break;                case 64:                    ic_sta = 6;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_clockWISE:0x%x",ges);                break;                case 128:                    ic_sta = 7;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_COUNT_CLOCKWISE:0x%x",ges);                break;                case 256:                    ic_sta = 8;                    sys_write_vp(0x1000,(u8*)&ic_sta,1);                 sprintf(text_buf,"GES_WAVE:0x%x",ges);                break;                default:                                        break;            }            len = strlen(text_buf);            text_buf[len++] = 0;            text_buf[len++] = 0;            sys_write_vp(0x2064,text_buf,len/2+1);//同時把數據包顯示到界面上                        uart2_rx_sta = 0;//清0代表處理掉了此串口包        }    }}

（左右移動查看全部內容）

3

小凌派方面

根據手勢demo將uart的demo加入到手勢demo.rar中，如下所示

/** Copyright (c) 2022 FuZhou Lockzhiner Electronic Co., Ltd. All rights reserved.* Licensed under the Apache License, Version 2.0 (the "License");* you may not use this file except in compliance with the License.* You may obtain a copy of the License at**   http://www.apache.org/licenses/LICENSE-2.0** Unless required by applicable law or agreed to in writing, software* distributed under the License is distributed on an "AS IS" BASIS,* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.* See the License for the specific language governing permissions and* limitations under the License.*/#include #include "los_task.h"#include "ohos_init.h"#include "lz_hardware.h"#include "e53_gesture_sensor.h"
/* E53模塊中* UART0_RX_M0 -> GPIO0_B6* UART0_TX_M0 -> GPIO0_B7*/#define UART_ID         0
unsigned short getCRC16(unsigned char *ptr,unsigned char len){        unsigned char i;        unsigned short crc = 0xFFFF;                if(ptr==0)        {                return 0;        }        if(len==0)        {            len = 1;        }        //if(len<=255)        {                while(len--)                {                        crc ^= *ptr;                        for(i=0; i<8; i++)                        {                            if(crc&1)                            {                                crc >>= 1;                                crc ^= 0xA001;                            }                            else                                crc >>= 1;                        }                        ptr++;                }        }        return(crc);}void uart0_init(void){  unsigned int ret;  UartAttribute attr;    LzUartDeinit(UART_ID);    attr.baudRate = 115200;  attr.dataBits = UART_DATA_BIT_8;  attr.pad = FLOW_CTRL_NONE;  attr.parity = UART_PARITY_NONE;  attr.rxBlock = UART_BLOCK_STATE_NONE_BLOCK;  attr.stopBits = UART_STOP_BIT_1;  attr.txBlock = UART_BLOCK_STATE_NONE_BLOCK;    PinctrlSet(GPIO0_PB6, MUX_FUNC2, PULL_KEEP, DRIVE_LEVEL2);  PinctrlSet(GPIO0_PB7, MUX_FUNC2, PULL_KEEP, DRIVE_LEVEL2);    ret = LzUartInit(UART_ID, &attr);  if (ret != LZ_HARDWARE_SUCCESS)  {    printf("%s, %d: LzUartInit(%d) faiLED!
", __FILE__, __LINE__, ret);    return;  }    return;}void e53_gs_process(void *arg){  unsigned int ret = 0;        unsigned int i=0;  unsigned short flag = 0;        unsigned short rc = 0;  unsigned char tubiao[16] = {0};        unsigned char tubiao_str[48] = {0};    e53_gs_init();  uart0_init();          ret = LzUartWrite(UART_ID, tubiao, 4);  if (ret != LZ_HARDWARE_SUCCESS)  {    printf("%s, %d: LzUartInit(%d) failed!
", __FILE__, __LINE__, ret);    return;  }    while (1)  {    ret = e53_gs_get_gesture_state(&flag);    if (ret != 0)    {      printf("Get Gesture Statu: 0x%x
", flag);      if (flag & GES_UP)      {        printf("	Up
");      }      if (flag & GES_DOWM)      {        printf("	Down
");      }      if (flag & GES_LEFT)      {        printf("	Left
");      }      if (flag & GES_RIGHT)      {        printf("	Right
");      }      if (flag & GES_FORWARD)      {        printf("	Forward
");      }      if (flag & GES_BACKWARD)      {        printf("	Backward
");      }      if (flag & GES_CLOCKWISE)      {        printf("	Clockwise
");      }      if (flag & GES_COUNT_CLOCKWISE)      {        printf("	Count Clockwise
");      }      if (flag & GES_WAVE)      {        printf("	Wave
");      }            e53_gs_led_up_set((flag & GES_UP) ? (1) : (0));      e53_gs_led_down_set((flag & GES_DOWM) ? (1) : (0));      e53_gs_led_left_set((flag & GES_LEFT) ? (1) : (0));      e53_gs_led_right_set((flag & GES_RIGHT) ? (1) : (0));      e53_gs_led_forward_set((flag & GES_FORWARD) ? (1) : (0));      e53_gs_led_backward_set((flag & GES_BACKWARD) ? (1) : (0));      e53_gs_led_cw_set((flag & GES_CLOCKWISE) ? (1) : (0));      e53_gs_led_ccw_set((flag & GES_COUNT_CLOCKWISE) ? (1) : (0));      e53_gs_led_wave_set((flag & GES_WAVE) ? (1) : (0));            tubiao[0] = flag;      tubiao[1] = (flag&0xff00)>>8;      tubiao[2] = '
';      tubiao[3] = '
';                        printf("tubiao：
");                        for(i=0;i<4;i++) {                            sprintf(tubiao_str+i*3, "%02X ", tubiao[i] & 0xFF);                        }                        printf("DOWN HEX: %s", tubiao_str);                        printf("
");      ret = LzUartWrite(UART_ID, tubiao, 4);      if (ret != LZ_HARDWARE_SUCCESS)      {        printf("%s, %d: LzUartInit(%d) failed!
", __FILE__, __LINE__, ret);        return;      }    }    else    {      /* 如果沒有數據，則多等待 */      LOS_Msleep(100);    }  }}
void e53_gs_example(){  unsigned int thread_id;  TSK_INIT_PARAM_S task = {0};  unsigned int ret = LOS_OK;
  task.pfnTaskEntry = (TSK_ENTRY_FUNC)e53_gs_process;  task.uwStackSize = 2048;  task.pcName = "e53 getsture sensor process";  task.usTaskPrio = 24;  ret = LOS_TaskCreate(&thread_id, &task);  if (ret != LOS_OK)  {    printf("Falied to create Task_One ret:0x%x
", ret);    return;  }}
APP_FEATURE_INIT(e53_gs_example);

（左右移動查看全部內容）

測試：測試的時候總是控制不了，用小凌派的串口發給電腦串口，也沒有。不應該，人家廠家肯定沒問題。本來2節杜邦線，改成了1節杜邦線，可以了。