欧美牲交aⅴ人妖,免费国产一级爱c视频2021,午夜三级a三级三点在线观看

9.1 原理圖分析

查看EK-RA6M4的原理圖，如下圖所示，該開發板上的 J11 提供了 Micro USB0接口。

根據原理圖可知，USB接口的引腳分別為：

功能	引腳USB
USB	USB_FS0
VBUS	P407

9.2 USB接口配置

首先，在FSP配置中將配置相關管腳為USB外設模式。

然后配置使能USB的48MHz時鐘。

接著選擇 Stacks ，點擊 "New Stack" -> "Connectivity" -> "USB PCDC(r_usb_pcdc)" 添加 USB CDC 協議棧。

接下來設置USB CDC的相關配置，并重新生成代碼。

9.3 源碼修改

創建按鍵操作相關的頭文件 src/r_usb_pcdc_descriptor.c ，該文件從瑞薩EK-RA6M4開發板的示例工程 ek_ra6m4\\usb_pcdc\\usb_pcdc_ek_ra6m4_ep 中拷貝過來。

/***********************************************************************************************************************
 * File Name    : r_usb_pcdc_descriptor.c
 * Description  : USB PCDC Descriptor definition.
 **********************************************************************************************************************/
/***********************************************************************************************************************
 * DISCLAIMER
 * This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products. No
 * other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all
 * applicable laws, including copyright laws.
 * THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING
 * THIS SOFTWARE, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. TO THE MAXIMUM
 * EXTENT PERMITTED NOT PROHIBITED BY LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES
 * SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS
 * SOFTWARE, EVEN IF RENESAS OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
 * Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability of
 * this software. By using this software, you agree to the additional terms and conditions found by accessing the
 * following link:
 * http://www.renesas.com/disclaimer
 *
 * Copyright (C) 2020 Renesas Electronics Corporation. All rights reserved.
 ***********************************************************************************************************************/

/******************************************************************************
 Includes   <System Includes> , "Project Includes"
 ******************************************************************************/
#include <r_usb_basic.h>
#include <r_usb_basic_api.h>
#include "r_usb_basic_cfg.h"

/******************************************************************************
 Macro definitions
 ******************************************************************************/
/* bcdUSB */
#define USB_BCDNUM                      (0x0200U)
/* Release Number */
#define USB_RELEASE                     (0x0200U)
/* DCP max packet size */
#define USB_DCPMAXP                     (64U)
/* Configuration number */
#define USB_CONFIGNUM                   (1U)
/* Vendor ID */
#define USB_VENDORID                    (0x045BU)
/* Product ID */
#define USB_PRODUCTID                   (0x5310U)

/* Class-Specific Configuration Descriptors */
#define     USB_PCDC_CS_INTERFACE                               (0x24U)

/* bDescriptor SubType in Communications Class Functional Descriptors */
/* Header Functional Descriptor */
#define     USB_PCDC_DT_SUBTYPE_HEADER_FUNC                     (0x00U)
/* Call Management Functional Descriptor. */
#define     USB_PCDC_DT_SUBTYPE_CALL_MANAGE_FUNC                (0x01U)
/* Abstract Control Management Functional Descriptor. */
#define     USB_PCDC_DT_SUBTYPE_ABSTRACT_CTR_MANAGE_FUNC        (0x02U)
/* Union Functional Descriptor */
#define     USB_PCDC_DT_SUBTYPE_UNION_FUNC                      (0x06U)

/* Communications Class Subclass Codes */
#define     USB_PCDC_CLASS_SUBCLASS_CODE_ABS_CTR_MDL            (0x02U)

/* USB Class Definitions for Communications Devices Specification
 release number in binary-coded decimal. */
#define     USB_PCDC_BCD_CDC          (0x0110U)

/* Descriptor length */
#define USB_PCDC_QD_LEN               (10U)
#define USB_PCDC_CD1_LEN              (67U)
#define STRING_DESCRIPTOR0_LEN        (4U)
#define STRING_DESCRIPTOR1_LEN        (16U)
#define STRING_DESCRIPTOR2_LEN        (44U)
#define STRING_DESCRIPTOR3_LEN        (46U)
#define STRING_DESCRIPTOR4_LEN        (22U)
#define STRING_DESCRIPTOR5_LEN        (18U)
#define STRING_DESCRIPTOR6_LEN        (28U)

/* Descriptor data Mask */
#define USB_UCHAR_MAX                 (0xffU)
#define USB_W_TOTAL_LENGTH_MASK       (256U)
#define USB_W_MAX_PACKET_SIZE_MASK    (64U)
#define USB_PCDC_BCD_CDC_MASK         (256U)

/******************************************************************************
 Private global variables and functions
 ******************************************************************************/

/******************************************************************************
 Exported global variables
 ******************************************************************************/

/******************************************************************************
 Exported global functions (to be accessed by other files)
 ******************************************************************************/

/* Standard Device Descriptor */
uint8_t g_apl_device[USB_DD_BLENGTH + ( USB_DD_BLENGTH % 2)] =
{
    USB_DD_BLENGTH,                                     /*  0:bLength */
    USB_DT_DEVICE,                                      /*  1:bDescriptorType */
    (USB_BCDNUM & (uint8_t) USB_UCHAR_MAX),                     /*  2:bcdUSB_lo */
    ((uint8_t) (USB_BCDNUM >> 8) & (uint8_t) USB_UCHAR_MAX),    /*  3:bcdUSB_hi */
    USB_IFCLS_CDCC,                                     /*  4:bDeviceClass */
    0,                                                  /*  5:bDeviceSubClass */
    0,                                                  /*  6:bDeviceProtocol */
    (uint8_t) USB_DCPMAXP,                              /*  7:bMAXPacketSize(for DCP) */
    (USB_VENDORID & (uint8_t) USB_UCHAR_MAX),                   /*  8:idVendor_lo */
    ((uint8_t) (USB_VENDORID >> 8) & (uint8_t) USB_UCHAR_MAX),  /*  9:idVendor_hi */
    ((uint16_t) USB_PRODUCTID & (uint8_t) USB_UCHAR_MAX),       /* 10:idProduct_lo */
    ((uint8_t) (USB_PRODUCTID >> 8) & (uint8_t) USB_UCHAR_MAX), /* 11:idProduct_hi */
    (USB_RELEASE & (uint8_t) USB_UCHAR_MAX),                    /* 12:bcdDevice_lo */
    ((uint8_t) (USB_RELEASE >> 8) & (uint8_t) USB_UCHAR_MAX),   /* 13:bcdDevice_hi */
    1,                                                  /* 14:iManufacturer */
    2,                                                  /* 15:iProduct */
    6,                                                  /* 16:iSerialNumber */
    USB_CONFIGNUM /* 17:bNumConfigurations */
};

/************************************************************
 *  Device Qualifier Descriptor   *
 ************************************************************/
uint8_t g_apl_qualifier_descriptor[USB_PCDC_QD_LEN + ( USB_PCDC_QD_LEN % 2)] =
{
    USB_PCDC_QD_LEN,                                    /*  0:bLength */
    USB_DT_DEVICE_QUALIFIER,                            /*  1:bDescriptorType */
    (USB_BCDNUM & (uint8_t) USB_UCHAR_MAX),                  /*  2:bcdUSB_lo */
    ((uint8_t) (USB_BCDNUM >> 8) & (uint8_t) USB_UCHAR_MAX), /*  3:bcdUSB_hi */
    0,                                                  /*  4:bDeviceClass */
    0,                                                  /*  5:bDeviceSubClass */
    0,                                                  /*  6:bDeviceProtocol */
    (uint8_t) USB_DCPMAXP,                              /*  7:bMAXPacketSize(for DCP) */
    USB_CONFIGNUM,                                      /*  8:bNumConfigurations */
    0 /*  9:bReserved */
};

/************************************************************
 *  Configuration Or Other_Speed_Configuration Descriptor   *
 ************************************************************/
/* For Full-Speed */
uint8_t g_apl_configuration[USB_PCDC_CD1_LEN + ( USB_PCDC_CD1_LEN % 2)] =
{
    USB_CD_BLENGTH,                 /*  0:bLength */
    USB_SOFT_CHANGE,                /*  1:bDescriptorType */
    USB_PCDC_CD1_LEN % USB_W_TOTAL_LENGTH_MASK, /*  2:wTotalLength(L) */
    USB_PCDC_CD1_LEN / USB_W_TOTAL_LENGTH_MASK, /*  3:wTotalLength(H) */
    2,                              /*  4:bNumInterfaces */
    1,                              /*  5:bConfigurationValue */
    0,                              /*  6:iConfiguration */
    USB_CF_RESERVED | USB_CF_SELFP, /*  7:bmAttributes */
    (10 / 2),                       /*  8:MAXPower (2mA unit) */

    /* Interface Descriptor */
    USB_ID_BLENGTH,                 /*  0:bLength */
    USB_DT_INTERFACE,               /*  1:bDescriptor */
    0,                              /*  2:bInterfaceNumber */
    0,                              /*  3:bAlternateSetting */
    1,                              /*  4:bNumEndpoints */
    USB_IFCLS_CDCC,                 /*  5:bInterfaceClass */
    USB_PCDC_CLASS_SUBCLASS_CODE_ABS_CTR_MDL,   /*  6:bInterfaceSubClass */
    1,                              /*  7:bInterfaceProtocol */
    0,                              /*  8:iInterface */

        /* Communications Class Functional Descriptorss */
        5,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_HEADER_FUNC,    /*  2:bDescriptorSubtype */
        USB_PCDC_BCD_CDC % USB_W_TOTAL_LENGTH_MASK,     /*  3:bcdCDC_lo */
        USB_PCDC_BCD_CDC / USB_W_TOTAL_LENGTH_MASK,     /*  4:bcdCDC_hi */

        /* Communications Class Functional Descriptorss */
        4,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_ABSTRACT_CTR_MANAGE_FUNC,   /*  2:bDescriptorSubtype */
        2,                          /*  3:bmCapabilities */

        /* Communications Class Functional Descriptorss */
        5,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_UNION_FUNC, /*  2:bDescriptorSubtype */
        0,                          /*  3:bMasterInterface */
        1,                          /*  4:bSlaveInterface0 */

        /* Communications Class Functional Descriptorss */
        5,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_CALL_MANAGE_FUNC,   /*  2:bDescriptorSubtype */
        /* D1:1-Device can send/receive call management
         information over a Data Class interface. */
        /* D0:1-Device handles call management itself. */
        3,                          /*  3:bmCapabilities */
        1,                          /*  4:bDataInterface */

        /* Endpoint Descriptor 0 */
        7,                          /*  0:bLength */
        USB_DT_ENDPOINT,            /*  1:bDescriptorType */
        USB_EP_IN | USB_EP3,        /*  2:bEndpointAddress */
        USB_EP_INT,                 /*  3:bmAttribute */
        16,                         /*  4:wMAXPacketSize_lo */
        0,                          /*  5:wMAXPacketSize_hi */
        0x10,                       /*  6:bInterval */

    /* Interface Descriptor */
    USB_ID_BLENGTH,                 /*  0:bLength */
    USB_DT_INTERFACE,               /*  1:bDescriptor */
    1,                              /*  2:bInterfaceNumber */
    0,                              /*  3:bAlternateSetting */
    2,                              /*  4:bNumEndpoints */
    USB_IFCLS_CDCD,                 /*  5:bInterfaceClass */
    0,                              /*  6:bInterfaceSubClass */
    0,                              /*  7:bInterfaceProtocol */
    0,                              /*  8:iInterface */

        /* Endpoint Descriptor 0 */
        USB_ED_BLENGTH,             /*  0:bLength */
        USB_DT_ENDPOINT,            /*  1:bDescriptorType */
        USB_EP_IN | USB_EP1,        /*  2:bEndpointAddress */
        USB_EP_BULK,                /*  3:bmAttribute */
        USB_W_MAX_PACKET_SIZE_MASK, /*  4:wMAXPacketSize_lo */
        0,                          /*  5:wMAXPacketSize_hi */
        0,                          /*  6:bInterval */

        /* Endpoint Descriptor 1 */
        USB_ED_BLENGTH,             /*  0:bLength */
        USB_DT_ENDPOINT,            /*  1:bDescriptorType */
        USB_EP_OUT | USB_EP2,       /*  2:bEndpointAddress */
        USB_EP_BULK,                /*  3:bmAttribute */
        USB_W_MAX_PACKET_SIZE_MASK, /*  4:wMAXPacketSize_lo */
        0,                          /*  5:wMAXPacketSize_hi */
        0,                          /*  6:bInterval */
};

/* For High-Speed */
uint8_t g_apl_hs_configuration[USB_PCDC_CD1_LEN + ( USB_PCDC_CD1_LEN % 2)] =
{
    9,                              /*  0:bLength */
    USB_SOFT_CHANGE,                /*  1:bDescriptorType */
    USB_PCDC_CD1_LEN % USB_W_TOTAL_LENGTH_MASK,         /*  2:wTotalLength(L) */
    USB_PCDC_CD1_LEN / USB_W_TOTAL_LENGTH_MASK,         /*  3:wTotalLength(H) */
    2,                              /*  4:bNumInterfaces */
    1,                              /*  5:bConfigurationValue */
    0,                              /*  6:iConfiguration */
    USB_CF_RESERVED | USB_CF_SELFP, /*  7:bmAttributes */
    (10 / 2),                       /*  8:MAXPower (2mA unit) */

    /* Interface Descriptor */
    9,                              /*  0:bLength */
    USB_DT_INTERFACE,               /*  1:bDescriptor */
    0,                              /*  2:bInterfaceNumber */
    0,                              /*  3:bAlternateSetting */
    1,                              /*  4:bNumEndpoints */
    USB_IFCLS_CDCC,                 /*  5:bInterfaceClass */
    USB_PCDC_CLASS_SUBCLASS_CODE_ABS_CTR_MDL,   /*  6:bInterfaceSubClass */
    1,                              /*  7:bInterfaceProtocol */
    0,                              /*  8:iInterface */

        /* Communications Class Functional Descriptorss */
        5, /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_HEADER_FUNC,    /*  2:bDescriptorSubtype */
        USB_PCDC_BCD_CDC % USB_PCDC_BCD_CDC_MASK,     /*  3:bcdCDC_lo */
        USB_PCDC_BCD_CDC / USB_PCDC_BCD_CDC_MASK,     /*  4:bcdCDC_hi */

        /* Communications Class Functional Descriptorss */
        4,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_ABSTRACT_CTR_MANAGE_FUNC,   /*  2:bDescriptorSubtype */
        2,                          /*  3:bmCapabilities */

        /* Communications Class Functional Descriptorss */
        5,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_UNION_FUNC, /*  2:bDescriptorSubtype */
        0,                          /*  3:bMasterInterface */
        1,                          /*  4:bSlaveInterface0 */

        /* Communications Class Functional Descriptorss */
        5,                          /*  0:bLength */
        USB_PCDC_CS_INTERFACE,      /*  1:bDescriptorType */
        USB_PCDC_DT_SUBTYPE_CALL_MANAGE_FUNC,   /*  2:bDescriptorSubtype */
        /* D1:1-Device can send/receive call management
         information over a Data Class interface. */
        /* D0:1-Device handles call management itself. */
        3,                          /*  3:bmCapabilities */
        1,                          /*  4:bDataInterface */

        /* Endpoint Descriptor 0 */
        7,                          /*  0:bLength */
        USB_DT_ENDPOINT,            /*  1:bDescriptorType */
        USB_EP_IN | USB_EP3,        /*  2:bEndpointAddress */
        USB_EP_INT,                 /*  3:bmAttribute */
        16,                         /*  4:wMAXPacketSize_lo */
        0,                          /*  5:wMAXPacketSize_hi */
        0x10,                       /*  6:bInterval */

    /* Interface Descriptor */
    9,                              /*  0:bLength */
    USB_DT_INTERFACE,               /*  1:bDescriptor */
    1,                              /*  2:bInterfaceNumber */
    0,                              /*  3:bAlternateSetting */
    2,                              /*  4:bNumEndpoints */
    USB_IFCLS_CDCD,                 /*  5:bInterfaceClass */
    0,                              /*  6:bInterfaceSubClass */
    0,                              /*  7:bInterfaceProtocol */
    0,                              /*  8:iInterface */

        /* Endpoint Descriptor 0 */
        7,                          /*  0:bLength */
        USB_DT_ENDPOINT,            /*  1:bDescriptorType */
        USB_EP_IN | USB_EP1,        /*  2:bEndpointAddress */
        USB_EP_BULK,                /*  3:bmAttribute */
        0,                          /*  4:wMAXPacketSize_lo */
        2,                          /*  5:wMAXPacketSize_hi */
        0,                          /*  6:bInterval */

        /* Endpoint Descriptor 1 */
        7,                          /*  0:bLength */
        USB_DT_ENDPOINT,            /*  1:bDescriptorType */
        USB_EP_OUT | USB_EP2,       /*  2:bEndpointAddress */
        USB_EP_BULK,                /*  3:bmAttribute */
        0,                          /*  4:wMAXPacketSize_lo */
        2,                          /*  5:wMAXPacketSize_hi */
        0,                          /*  6:bInterval */
};

/*************************************
 *    String Descriptor              *
 *************************************/
/* UNICODE 0x0409 English (United States) */
uint8_t g_cdc_string_descriptor0[STRING_DESCRIPTOR0_LEN + ( STRING_DESCRIPTOR0_LEN % 2)] =
{
    STRING_DESCRIPTOR0_LEN,     /*  0:bLength */
    USB_DT_STRING,              /*  1:bDescriptorType */
    0x09, 0x04                  /*  2:wLANGID[0] */
};

/* iManufacturer */
uint8_t g_cdc_string_descriptor1[STRING_DESCRIPTOR1_LEN + ( STRING_DESCRIPTOR1_LEN % 2)] =
{
    STRING_DESCRIPTOR1_LEN,     /*  0:bLength */
    USB_DT_STRING,              /*  1:bDescriptorType */
    'R', 0x00,                  /*  2:wLANGID[0] */
    'E', 0x00,
    'N', 0x00,
    'E', 0x00,
    'S', 0x00,
    'A', 0x00,
    'S', 0x00,
};

/* iProduct */
uint8_t g_cdc_string_descriptor2[STRING_DESCRIPTOR2_LEN + ( STRING_DESCRIPTOR2_LEN % 2)] =
{
    STRING_DESCRIPTOR2_LEN, /*  0:bLength */
    USB_DT_STRING,          /*  1:bDescriptorType */
    'C', 0x00,
    'D', 0x00,
    'C', 0x00,
    ' ', 0x00,
    'U', 0x00,
    'S', 0x00,
    'B', 0x00,
    ' ', 0x00,
    'D', 0x00,
    'e', 0x00,
    'm', 0x00,
    'o', 0x00,
    'n', 0x00,
    's', 0x00,
    't', 0x00,
    'r', 0x00,
    'a', 0x00,
    't', 0x00,
    'i', 0x00,
    'o', 0x00,
    'n', 0x00,
};

/* iInterface */
uint8_t g_cdc_string_descriptor3[STRING_DESCRIPTOR3_LEN + ( STRING_DESCRIPTOR3_LEN % 2)] =
{
    STRING_DESCRIPTOR3_LEN, /*  0:bLength */
    USB_DT_STRING,          /*  1:bDescriptorType */
    'C', 0x00,
    'o', 0x00,
    'm', 0x00,
    'm', 0x00,
    'u', 0x00,
    'n', 0x00,
    'i', 0x00,
    'c', 0x00,
    'a', 0x00,
    't', 0x00,
    'i', 0x00,
    'o', 0x00,
    'n', 0x00,
    's', 0x00,
    ' ', 0x00,
    'D', 0x00,
    'e', 0x00,
    'v', 0x00,
    'i', 0x00,
    'c', 0x00,
    'e', 0x00,
    's', 0x00
};

/* iConfiguration */
uint8_t g_cdc_string_descriptor4[STRING_DESCRIPTOR4_LEN + ( STRING_DESCRIPTOR4_LEN % 2)] =
{
    STRING_DESCRIPTOR4_LEN, /*  0:bLength */
    USB_DT_STRING,          /*  1:bDescriptorType */
    'F', 0x00,              /*  2:wLANGID[0] */
    'u', 0x00,
    'l', 0x00,
    'l', 0x00,
    '-', 0x00,
    'S', 0x00,
    'p', 0x00,
    'e', 0x00,
    'e', 0x00,
    'd', 0x00
};

/* iConfiguration */
uint8_t g_cdc_string_descriptor5[STRING_DESCRIPTOR5_LEN + ( STRING_DESCRIPTOR5_LEN % 2)] =
{
    STRING_DESCRIPTOR5_LEN, /*  0:bLength */
    USB_DT_STRING,          /*  1:bDescriptorType */
    'H', 0x00,              /*  2:wLANGID[0] */
    'i', 0x00,
    '-', 0x00,
    'S', 0x00,
    'p', 0x00,
    'e', 0x00,
    'e', 0x00,
    'd', 0x00
};

/* iSerialNumber */
uint8_t g_cdc_string_descriptor6[STRING_DESCRIPTOR6_LEN + ( STRING_DESCRIPTOR6_LEN % 2)] =
{
    STRING_DESCRIPTOR6_LEN, /*  0:bLength */
    USB_DT_STRING,          /*  1:bDescriptorType */
    '0', 0x00,              /*  2:wLANGID[0] */
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '0', 0x00,
    '1', 0x00,
};

uint8_t *g_apl_string_table[] =
{
    g_cdc_string_descriptor0,
    g_cdc_string_descriptor1,
    g_cdc_string_descriptor2,
    g_cdc_string_descriptor3,
    g_cdc_string_descriptor4,
    g_cdc_string_descriptor5,
    g_cdc_string_descriptor6
};

/******************************************************************************
 Renesas Abstracted Peripheral Communications Devices Class Driver API functions
 ******************************************************************************/

/******************************************************************************
 End  Of File
 ******************************************************************************/

修改 src/hal_entry.c 源文件，在里面添加 USB CDC相關代碼如下。

... ...
#define APP_ERR_TRAP(a)             if(a) {__asm("BKPT #0
");} /* trap the error location */

/* Global variables */
extern uint8_t  g_apl_device[];
extern uint8_t  g_apl_configuration[];
extern uint8_t  g_apl_hs_configuration[];
extern uint8_t  g_apl_qualifier_descriptor[];
extern uint8_t *g_apl_string_table[];

#define LINE_CODING_LENGTH          (0x07U)
#define READ_BUF_SIZE               (8U)
#define NUM_STRING_DESCRIPTOR       (7U)
const usb_descriptor_t usb_descriptor =
{
 g_apl_device,                   /* Pointer to the device descriptor */
 g_apl_configuration,            /* Pointer to the configuration descriptor for Full-speed */
 g_apl_hs_configuration,         /* Pointer to the configuration descriptor for Hi-speed */
 g_apl_qualifier_descriptor,     /* Pointer to the qualifier descriptor */
 g_apl_string_table,             /* Pointer to the string descriptor table */
 NUM_STRING_DESCRIPTOR
};

usb_status_t            usb_event;
static bool  b_usb_attach = false;

static fsp_err_t usb_pcdc_echo_back(char *p_data);

... ...

void hal_entry(void)
{
    /* TODO: add your own code here */
    fsp_err_t err                           = FSP_SUCCESS;
    usb_event_info_t    event_info          = {0};
    uint8_t g_buf[READ_BUF_SIZE]            = {0};
    static usb_pcdc_linecoding_t g_line_coding;

    R_BSP_PinAccessEnable(); /* Enable access to the PFS registers. */

    console_initialize();
    printf("Hello EK-RA6M4 Board
");

    /* Open USB instance */
    err = R_USB_Open (&g_basic0_ctrl, &g_basic0_cfg);
    /* Handle error */
    if (FSP_SUCCESS != err)
    {
        /* Turn ON RED LED to indicate fatal error */
        turn_led(BSP_LEDRED, BSP_LEDON);
        APP_ERR_TRAP(err);
    }

    while (1)
    {
        /* Obtain USB related events */
        err = R_USB_EventGet (&event_info, &usb_event);

        /* Handle error */
        if (FSP_SUCCESS != err)
        {
            /* Turn ON RED LED to indicate fatal error */
            turn_led(BSP_LEDRED, BSP_LEDON);
            APP_ERR_TRAP(err);
        }

        /* USB event received by R_USB_EventGet */
        switch (usb_event)
        {
            case USB_STATUS_CONFIGURED:
            {
                err = R_USB_Read (&g_basic0_ctrl, g_buf, READ_BUF_SIZE, USB_CLASS_PCDC);
                /* Handle error */
                if (FSP_SUCCESS != err)
                {
                    /* Turn ON RED LED to indicate fatal error */
                    turn_led(BSP_LEDRED, BSP_LEDON);
                    APP_ERR_TRAP(err);
                }

                break;
            }

            case USB_STATUS_READ_COMPLETE:
            {
                if(b_usb_attach)
                {
                    err = R_USB_Read (&g_basic0_ctrl, g_buf, READ_BUF_SIZE, USB_CLASS_PCDC);
                }
                /* Handle error */
                if (FSP_SUCCESS != err)
                {
                    /* Turn ON RED LED to indicate fatal error */
                    turn_led(BSP_LEDRED, BSP_LEDON);
                    APP_ERR_TRAP(err);
                }

                usb_pcdc_echo_back((char *)g_buf);
                printf("USB read data: 0x%02x->%c
", g_buf[0], g_buf[0]);
                break;
            }

            case USB_STATUS_REQUEST : /* Receive Class Request */
            {
                /* Check for the specific CDC class request IDs */
                if (USB_PCDC_SET_LINE_CODING == (event_info.setup.request_type & USB_BREQUEST))
                {
                    err =  R_USB_PeriControlDataGet (&g_basic0_ctrl, (uint8_t *) &g_line_coding, LINE_CODING_LENGTH );
                    /* Handle error */
                    if (FSP_SUCCESS != err)
                    {
                        /* Turn ON RED LED to indicate fatal error */
                        turn_led(BSP_LEDRED, BSP_LEDON);
                        APP_ERR_TRAP(err);
                    }
                }
                else if (USB_PCDC_GET_LINE_CODING == (event_info.setup.request_type & USB_BREQUEST))
                {
                    err =  R_USB_PeriControlDataSet (&g_basic0_ctrl, (uint8_t *) &g_line_coding, LINE_CODING_LENGTH );
                    /* Handle error */
                    if (FSP_SUCCESS != err)
                    {
                        /* Turn ON RED LED to indicate fatal error */
                        turn_led(BSP_LEDRED, BSP_LEDON);
                        APP_ERR_TRAP(err);
                    }
                }
                else if (USB_PCDC_SET_CONTROL_LINE_STATE == (event_info.setup.request_type & USB_BREQUEST))
                {
                    err = R_USB_PeriControlStatusSet (&g_basic0_ctrl, USB_SETUP_STATUS_ACK);
                    /* Handle error */
                    if (FSP_SUCCESS != err)
                        //if (FSP_SUCCESS != g_err)
                    {
                        /* Turn ON RED LED to indicate fatal error */
                        turn_led(BSP_LEDRED, BSP_LEDON);
                        APP_ERR_TRAP(err);
                    }
                }
                else
                {
                    /* none */
                }

                break;
            }

            case USB_STATUS_DETACH:
            case USB_STATUS_SUSPEND:
            {
                b_usb_attach = false;
                memset (g_buf, 0, sizeof(g_buf));
                break;
            }
            case USB_STATUS_RESUME:
            {
                b_usb_attach = true;
                break;
            }
            default:
            {
                break;
            }
        }
    }

#if BSP_TZ_SECURE_BUILD
    /* Enter non-secure code */
    R_BSP_NonSecureEnter();
#endif
}

/*****************************************************************************************************************
 *  @brief      Check for write completion
 *  @param[in]  None
 *  @retval     FSP_SUCCESS     Upon success
 *  @retval     any other error code apart from FSP_SUCCESS
 ****************************************************************************************************************/
static fsp_err_t check_for_write_complete(void)
{
    usb_status_t usb_write_event = USB_STATUS_NONE;
    int32_t timeout_count = UINT16_MAX;
    fsp_err_t err = FSP_SUCCESS;
    usb_event_info_t    event_info = {0};

    do
    {
        err = R_USB_EventGet (&event_info, &usb_write_event);
        if (FSP_SUCCESS != err)
        {
            return err;
        }

        --timeout_count;

        if (0 > timeout_count)
        {
            timeout_count = 0;
            err = (fsp_err_t)USB_STATUS_NONE;
            break;
        }
    }while(USB_STATUS_WRITE_COMPLETE != usb_write_event);

    return err;
}

/*****************************************************************************************************************
 *  @brief      Prints the message to console
 *  @param[in]  p_msg contains address of buffer to be printed
 *  @retval     FSP_SUCCESS     Upon success
 *  @retval     any other error code apart from FSP_SUCCESS, Write is unsuccessful
 ****************************************************************************************************************/
static fsp_err_t usb_pcdc_echo_back(char *p_data)
{
    fsp_err_t err = FSP_SUCCESS;
    uint32_t len = ((uint32_t)strlen(p_data));

    err = R_USB_Write (&g_basic0_ctrl, (uint8_t*)p_data, len, USB_CLASS_PCDC);
    /* Handle error */
    if (FSP_SUCCESS != err)
    {
        return err;
    }

    err = check_for_write_complete();
    if (FSP_SUCCESS != err)
    {
        /* Did not get the event hence returning error */
        return FSP_ERR_USB_FAILED;
    }
    return err;
}

9.4 編譯運行

代碼修改完成后，在開發板上編譯運行。將J11上的Micro USB接到電腦上，在Window的設備管理器上將會看到新的串口設備(如下面的COM9)。

接下來在USB的虛擬串口COM9上發送數據，將會收到回顯數據，另外Console串口上也會打印收到的數據。

聲明：本文內容及配圖由入駐作者撰寫或者入駐合作網站授權轉載。文章觀點僅代表作者本人，不代表電子發燒友網立場。文章及其配圖僅供工程師學習之用，如有內容侵權或者其他違規問題，請聯系本站處理。舉報投訴

單片機

單片機

+關注

關注
6030

文章
44489

瀏覽量
631974
接口

接口

+關注

關注
33

文章
8447

瀏覽量
150720
usb

usb

+關注

關注
60

文章
7876

瀏覽量
263697
CDC

CDC

+關注

關注
0

文章
57

瀏覽量
17747

評論

相關推薦

單片機必須了解的外設功能——GPIO/串行通信

活學活用單片機連載將介紹有效使用單片機外設功能的結構及使用方法，能讓我們將能學到各種單片機共通的基本外設功能，并可廣泛應用到各個方面。

發表于 09-07 10:45 ?1.8w次閱讀

stm32cubemx配置單片機的USB外設為CDC模式，燒寫程序時出錯怎么解決？

我用的單片機型號是STM32L496VGT3,按照網上的教程用STM32CUBEMX將單片機的USB外設配置為CDC模式，生成代碼之后在燒寫

發表于 04-29 08:09

stm32cubemx配置單片機的USB外設為CDC模式，燒寫程序時出錯

我用的單片機型號是STM32L496VGT3,按照網上的教程用STM32CUBEMX將單片機的USB外設配置為CDC模式，生成代碼之后在燒寫

發表于 05-08 14:33

STM32 USB如何配置多個CDC設備

項需求，在STM32F072中需實現5個CDC設備,折騰了很久分享出來，希望能幫助別人少踩一些坑.USB2.0全速,該款單片機支持8個輸出和８?jìng)€(gè)輸入端點，過程中參考了些大佬的貼子STM

發表于 02-22 07:28

一些AVR的單片機沒有USB外設，但是可以接usb是為什么？

一些AVR的單片機，沒有USB外設，但是可以接usb，為什么

發表于 09-25 08:14

USB接口類單片機特點及應用

USB接口已經在無線接入設備、電子商務、安全鑰匙、PDA及計算機便攜式外設上有了廣泛的應用。本次Freescale杯設計競賽推薦的兩款單片機帶有USB接口，它們是支持高速、全速

發表于 04-22 16:46 ?22次下載

基于單片機的嵌入式USB主機系統的實現

在無操作系統的單片機系統中實現USB主機系統功能，對U盤進行文件的讀寫，并在U盤上實現FAT格式文件系統，使U盤成為單片機應用系統的存儲設備

發表于 09-16 09:21 ?30次下載

USB2.0特性及USB單片機

USB2.0特性及USB單片機:通用串行總線USB（Universal Serial Bus）是由Intel等廠商制定的連接計算機與具有USB

發表于 09-19 08:09 ?72次下載

USB接口類單片機特點及應用

USB接口已經在無線接入設備、電子商務、安全鑰匙、PDA及計算機便攜式外設上有了廣泛的應用。本次Freescale杯設計競賽推薦的兩款單片機帶有USB接

發表于 03-11 12:23 ?1301次閱讀

USB接口類單片機特點及應用

USB接口類單片機特點及應用USB接口已經在無線接入設備、電子商務、安全鑰、PDA及計算機便攜式外設上有了廣泛的應用。本次‘Freescale杯’設

發表于 04-11 17:08 ?2052次閱讀

單片機外設有哪些,外設功能是什么?

單片機內部的外設一般包括：串口控制模塊，SPI模塊，I2C模塊，A/D模塊，PWM模塊，CAN模塊，EEPROM，比較器模塊，等等，它們都集成在單片機內部，有相對應的內部控制寄存器，可通過單片

發表于 11-16 11:23 ?4.9w次閱讀

怎么學習單片機外設

雖然題主只是問了怎么學習單片機外設，但我認為，外設的學習與單片機的片上資源同時學習最好，給自己一個項目題目然后動手去寫代碼是最好的。單片機的

發表于 05-07 14:51 ?4105次閱讀

單片機外設和編程的學習課件免費下載

本文檔的主要內容詳細介紹的是單片機外設和編程的學習課件免費下載

發表于 06-15 08:00 ?1次下載

STM32 USB如何配置多個CDC設備—5個CDC設備

項需求，在STM32F072中需實現5個CDC設備,折騰了很久分享出來，希望能幫助別人少踩一些坑.USB2.0全速,該款單片機支持8個輸出和８?jìng)€(gè)輸入端點，過程中參考了些大佬的貼子STM

發表于 12-28 19:43 ?30次下載

基于單片機的USB主從機的設計與實現

電子發燒友網站提供《基于單片機的USB主從機的設計與實現.pdf》資料免費下載

發表于 10-19 10:54 ?0次下載