【項目移植】N32WB03xSTB開發板ADC實驗

1. 前言

本教程基于【N32WB03x SDK使用指南】的開發環境，結合官方教程開展的N32WB03xSTB開發板ADC實驗，主要由讀取兩路ADC并打印實驗和讀取板載芯片溫度實驗兩部分組成。

2. ADC 功能描述

2.1 輸入通道和輸入電壓范圍

ADC 是一種高速逐次逼近型模擬數字轉換器。有多達 8 個通道，5 個外部單端，1 個差分 MIC 和 2 個內部通道。內部通道包括 VCC 檢測通道和溫度傳感器通道。各通道的 A/D 轉換可以單次、連續模式執行。配置 ADC_CTRL.ADC_CH_SEL 用于 ADC 輸入通道選擇。

000（默認）選擇差分 MIC 通路，對應 PB11/PB13，001～010 用于片外預分壓輸入，對應PB9/PB10，無阻性負載，檢測范圍 0.125～0.85V，011～101 用于直接檢測，對應 PB6~PB8，輸入阻抗360K?，檢測范圍 0.5～3.5V，110 用于 VCC 檢測，111 用于片內溫度傳感器電壓檢測。

2.2 ADC 開關控制

通過設置 ADC_CTRL 寄存器的 ADC_EN 位可啟動 ADC。當?shù)谝淮卧O(shè)置 ADC_EN 位時，ADC 在開始精確轉換前需要一個穩定時間 tSTAB 64 cycle。之后每個 Cycle 進行一次轉換。在單次模式下，轉換完成后，硬件自動關閉 ADC_EN 位。如使能中斷，可產生轉換結束中斷。用戶可以通過查詢 ADC_SR 里面的 ADC_DONE_F 確認轉換是否完成。在連續模式下，通過清除 ADC_EN 位可以停止轉換。輸入通道切換前需要先關閉 ADC_EN 位。

2.3 轉換模式

2.3.1 單次轉換模式

每個轉換有兩個階段：采樣階段和轉換階段。單次轉換模式下，ADC 只執行一次轉換。設置 ADC_CTRL.ADC_CH_SEL 選擇輸入通道后，可通過設置ADC_CTRL 寄存器的 ADC_EN 位啟動。一旦選擇通道的轉換完成：

• 轉換數據被儲存在 16 位 ADC_DAT 寄存器中

• ADC_DONE_F（轉換結束）標志被設置

• 如果設置了ADC_DONE_IE，則產生中斷。

轉換本身很快，只需要一個 adcclk 的時鐘周期。但單次模式下，ADCEN 或 ADCSEL 修改后，輸入通道的切換電路需要 64 個adcclk 穩定時間。

2.3.2 連續轉換模式

將 ADC_CTRL.ADC_MODE 置為“1”可以在連續模式下使用 ADC，在連續轉換模式中，當前面 ADC 轉換一結束馬上就啟動另一次轉換。設置 ADC_CTRL.ADC_CH_SEL 選擇輸入通道后，可通過設置ADC_CTRL 寄存器的 ADC_EN 位來觸發第一次轉換，但之后，將每個 adcclk 周期自動生成新的轉換數據。支持過采樣率設置，配置值 ADC_OVR_SAMP_CNT. OS_CNT_LD_CNT 需要>=2，OS_CNT_LD_CNT+1個數據采樣一個數據。

每個轉換后：

• 轉換數據被儲存在 16 位的 ADC_DAT 寄存器中

• 使能 DMA 模式，每次轉換后會產生 DMA 請求

2.4 模擬看門狗

如果被 ADC 轉換的模擬 PB10 電壓低于低閾值或高于高閾值，AWDG 模擬看門狗狀態位被設置。閾值位于ADC_ WDHIGH 和 ADC_WDLOW 寄存器的最低 10 個有效位中。通過設置 ADC_CTRL 寄存器的 AWD_IE位以允許產生相應中斷。

3. ADC 實驗

3.1 兩路ADC并打印實驗

項目文件地址：N32WB03x_SDK V1.2.0N32WB03x_SDK V1.2.0projects 32wb03x_EVALperipheralADCADC_SingleReadMDK-ARM

3.1.1 打開工程

keil5 打開后查看相關程序函數

項目簡介在readme.txt

1、功能說明


 此例程提供了ADC單次轉換的實現。
    
2、使用環境


  軟件開發環境：KEIL MDK-ARM V5.26.2.0
  
  硬件環境：
    1、基于N32WB031_STB開發板
    2、MCU：N32WB031


3、使用說明 
  
  1、系統時鐘：64MHz
  2、ADC通道：ADC_CTRL_CH_1(PB10)、ADC_CTRL_CH_3(PB8)


  
  日志打?。簭哪Ｊ?DEMO 板 PB6(TX)，波特率：115200
  
  測試步驟與現象：
    a，編譯下載代碼復位運行
    b，從串口看打印信息，驗證結果兩個通道ADC轉換的電壓
    
4、注意事項
  開發板的J15 短接右邊，J16 短接左邊，選擇 IO 連接到排針。

（左右移動查看全部內容）

3.1.2 配置工程

主程序main.c

/*****************************************************************************
 * Copyright (c) 2019, Nations Technologies Inc.
 *
 * All rights reserved.
 * ****************************************************************************
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Nations' name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY NATIONS "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL NATIONS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ****************************************************************************/


/**
 * [url=home.php?mod=space&uid=1455510]@file[/url] main.c
 * [url=home.php?mod=space&uid=40524]@author[/url] Nations Firmware Team
 * [url=home.php?mod=space&uid=644434]@version[/url] v1.0.2
 *
 * [url=home.php?mod=space&uid=855824]@copyright[/url] Copyright (c) 2019, Nations Technologies Inc. All rights reserved.
 */
#include "main.h"
#include "log.h"


void RCC_Configuration(void);
void GPIO_Configuration(void);
void ADC_Configuration(void);


uint16_t ADCConvertedValue[2];
uint32_t voltage[2] = {0}; 
/**
 * [url=home.php?mod=space&uid=2666770]@Brief[/url] Main program
 */
int main(void)
{
 log_init();
  log_info("
this is adc single read Demo.
");
 log_info("Please make sure J15 and J16 connect the IO to pin on board!
");
 /* System Clocks Configuration */
 RCC_Configuration();
 
 /* Configure the GPIO ports */
  GPIO_Configuration();
 
 ADC_EnableBypassFilter(ADC, ENABLE);
  while (1)
  {
  ADC_ConfigChannel(ADC, ADC_CTRL_CH_3);
  ADC_Enable(ADC, ENABLE);
  while(ADC_GetFlagStatus(ADC,ADC_FLAG_DONE) == RESET);
  ADC_ClearFlag(ADC,ADC_FLAG_DONE); 
  ADCConvertedValue[1] = ADC_GetDat(ADC);
  
  voltage[1] = ADC_ConverValueToVoltage(ADCConvertedValue[1], ADC_CTRL_CH_3);
  log_info("ADC CH3 value: %4d | ADC CH3 vol_mV: %4d .
",ADCConvertedValue[1],voltage[1]); 
 
  ADC_ConfigChannel(ADC, ADC_CTRL_CH_1);
  ADC_Enable(ADC, ENABLE);
  while(ADC_GetFlagStatus(ADC,ADC_FLAG_DONE) == RESET);
  ADC_ClearFlag(ADC,ADC_FLAG_DONE); 
  ADCConvertedValue[0] = ADC_GetDat(ADC);


  voltage[0] = ADC_ConverValueToVoltage(ADCConvertedValue[0], ADC_CTRL_CH_1);
  log_info("ADC CH1 value: %4d | ADC CH1 vol_mV: %4d .

",ADCConvertedValue[0],voltage[0]);  
  Delay_ms(1000);
  }
}




/**
 * @brief Configures the different system clocks.
 */
void RCC_Configuration(void)
{
 /* Enable peripheral clocks */
  /* Enable GPIOB clocks */
  RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOB, ENABLE);
  /* Enable ADC clocks */
  RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC, ENABLE);
    
  RCC_ConfigAdcClk(RCC_ADCCLK_SRC_AUDIOPLL);


  /* enable ADC 4M clock */
  RCC_Enable_ADC_CLK_SRC_AUDIOPLL(ENABLE);
}




/**
 * @brief Configures the different GPIO ports.
 */
void GPIO_Configuration(void)
{
  GPIO_InitType GPIO_InitStructure;


  GPIO_InitStruct(&GPIO_InitStructure);
  /* Configure PB.10 (ADC Channel1) PB.8 (ADC Channel3) as analog input --------*/
  GPIO_InitStructure.Pin    = GPIO_PIN_10|GPIO_PIN_8;
  GPIO_InitStructure.GPIO_Mode = GPIO_MODE_ANALOG;
  GPIO_InitPeripheral(GPIOB, &GPIO_InitStructure);
}




#ifdef USE_FULL_ASSERT


/**
 * @brief Reports the name of the source file and the source line number
 *     where the assert_param error has occurred.
 * @param file pointer to the source file name
 * @param line assert_param error line source number
 */
void assert_failed(const uint8_t* expr, const uint8_t* file, uint32_t line)
{
  /* User can add his own implementation to report the file name and line number,
   ex: printf("Wrong parameters value: file %s on line %d
", file, line) */


  while (1)
  {
  }
}


#endif


/**
 * @}
 */


/**
 * @}
 */


/*************** (C) COPYRIGHT Nations Technologies Inc *****END OF FILE***************/

（左右移動查看全部內容）

此部分不修改

3.1.3 編譯下載

N32WB03xSTB開發板自帶下載器，官方已經配置好了，直接連接Type-C編譯下載

3.1.4 調試驗證

打開串口調試助手，修改相關配置。連接開發板，打印效果如下

此時可以用GND或者3.3V電源用杜邦線短接ADC_CTRL_CH_1(PB10)、ADC_CTRL_CH_3(PB8)
，也會有相關大小變化

[11:38:01.339]收←◆ADC CH3 value:  64 | ADC CH3 vol_mV:  77 .
ADC CH1 value: 502 | ADC CH1 vol_mV: 496 .




[11:38:02.373]收←◆ADC CH3 value:  65 | ADC CH3 vol_mV:  81 .
ADC CH1 value: 527 | ADC CH1 vol_mV: 523 .




[11:38:03.408]收←◆ADC CH3 value:  64 | ADC CH3 vol_mV:  77 .
ADC CH1 value: 880 | ADC CH1 vol_mV: 908 .




[11:38:04.442]收←◆ADC CH3 value:  66 | ADC CH3 vol_mV:  86 .
ADC CH1 value: 159 | ADC CH1 vol_mV: 123 .




[11:38:05.477]收←◆ADC CH3 value:  65 | ADC CH3 vol_mV:  81 .
ADC CH1 value: 750 | ADC CH1 vol_mV: 767 .




[11:38:06.511]收←◆ADC CH3 value:  59 | ADC CH3 vol_mV:  55 .
ADC CH1 value: 789 | ADC CH1 vol_mV: 809 .

（左右移動查看全部內容）

3.2 讀取板載芯片溫度實驗

項目文件地址：N32WB03x_SDK V1.2.0projects 32wb03x_EVALperipheralADCADC_TemperatureMDK-ARM

3.2.1 打開工程

keil5 打開后查看相關程序函數

項目簡介在readme.txt

1、功能說明


 此例程提供了ADC溫度傳感通道轉換的實現。
    
2、使用環境


  軟件開發環境：KEIL MDK-ARM V5.26.2.0
  
  硬件環境：
    1、基于N32WB031_STB開發板
    2、MCU：N32WB031


3、使用說明 
  
  1、系統時鐘：64MHz
  2、ADC通道：ADC_CTRL_CH_7(TS)


  
  日志打?。簭哪Ｊ?DEMO 板 PB6(TX)，波特率：115200
  
  測試步驟與現象：
    a，編譯下載代碼復位運行
    b，從串口看打印信息，驗證溫度傳感通道ADC轉換的結果
    
4、注意事項
  無

（左右移動查看全部內容）

3.2.2 配置工程

主程序main.c

/*****************************************************************************
 * Copyright (c) 2019, Nations Technologies Inc.
 *
 * All rights reserved.
 * ****************************************************************************
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Nations' name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY NATIONS "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL NATIONS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ****************************************************************************/


/**
 * @file main.c
 * @author Nations Firmware Team
 * @version v1.0.2
 *
 * @copyright Copyright (c) 2019, Nations Technologies Inc. All rights reserved.
 */
 
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "log.h"
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
#define ADC_BUF_SIZE   (10)


/* Private constants ---------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
uint16_t ADCConvertedBuffer[ADC_BUF_SIZE];
uint16_t ADCConvertedValue;
uint32_t Voltage_mA; 
float Temperature; 
/* Private function prototypes -----------------------------------------------*/
void RCC_Configuration(void);
void GPIO_Configuration(void);
void ADC_Configuration(void);
/* Private functions ---------------------------------------------------------*/




/**
 * @brief Main program
 */
int main(void)
{
  DMA_InitType DMA_InitStructure;
  uint32_t adc_sum,i;
  
  log_init();
  log_info("
this is adc temperature sensor read demo.
");
  
  /* System Clocks Configuration */
  RCC_Configuration();
  
  /* Configure the GPIO ports */
  GPIO_Configuration();
  
  /* DMA channel1 configuration ----------------------------------------------*/
  DMA_DeInit(DMA_CH1);
  DMA_InitStructure.PeriphAddr   = (uint32_t)&ADC->DAT;
  DMA_InitStructure.MemAddr    = (uint32_t)ADCConvertedBuffer;
  DMA_InitStructure.Direction   = DMA_DIR_PERIPH_SRC;
  DMA_InitStructure.BufSize    = ADC_BUF_SIZE;
  DMA_InitStructure.PeriphInc   = DMA_PERIPH_INC_DISABLE;
  DMA_InitStructure.DMA_MemoryInc = DMA_MEM_INC_ENABLE;
  DMA_InitStructure.PeriphDataSize = DMA_PERIPH_DATA_SIZE_HALFWORD;
  DMA_InitStructure.MemDataSize  = DMA_MemoryDataSize_HalfWord;
  DMA_InitStructure.CircularMode  = DMA_MODE_CIRCULAR;
  DMA_InitStructure.Priority    = DMA_PRIORITY_HIGH;
  DMA_InitStructure.Mem2Mem    = DMA_M2M_DISABLE;
  DMA_Init(DMA_CH1, &DMA_InitStructure);
  DMA_RequestRemap(DMA_REMAP_ADC, DMA, DMA_CH1, ENABLE);


  /* Enable DMA channel 1 */
  DMA_EnableChannel(DMA_CH1, ENABLE);
  ADC_SetOverSampleCounter(ADC,3);
  ADC_EnableBypassFilter(ADC, ENABLE);
  ADC_ConfigChannel(ADC, ADC_CTRL_CH_7);
  ADC_ConfigContinuousMode(ADC, ENABLE);
  ADC_EnableDMA(ADC, ENABLE);
  ADC_EnableTS(ADC, ENABLE);
  ADC_Enable(ADC, ENABLE);


  while (1)
  {


    /* Transfer complete */
    while (!DMA_GetFlagStatus(DMA_FLAG_TC1, DMA));
    adc_sum = 0;
    for(i=0;i    {
      adc_sum += ADCConvertedBuffer[i];
    }
    ADCConvertedValue = adc_sum/ADC_BUF_SIZE;
    Temperature = ADC_ConverValueToTemperature(ADCConvertedValue);
    log_info("ADC temperature sensor: %.2f C
",Temperature); 


    Delay_ms(1000);
  }
}




/**
 * @brief Configures the different system clocks.
 */
void RCC_Configuration(void)
{
  /* Enable peripheral clocks */
  RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_DMA, ENABLE);
  /* Enable GPIOB clocks */
  RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOB, ENABLE);
  /* Enable ADC clocks */
  RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC, ENABLE);
    
  RCC_ConfigAdcClk(RCC_ADCCLK_SRC_AUDIOPLL);


  /* enable ADC 4M clock */
  RCC_Enable_ADC_CLK_SRC_AUDIOPLL(ENABLE);
}




/**
 * @brief Configures the different GPIO ports.
 */
void GPIO_Configuration(void)
{
  GPIO_InitType GPIO_InitStructure;


  GPIO_InitStruct(&GPIO_InitStructure);
  /* Configure PB.10 (ADC Channel1) PB.7 (ADC Channel4) as analog input --------*/
  GPIO_InitStructure.Pin    = GPIO_PIN_10|GPIO_PIN_7;
  GPIO_InitStructure.GPIO_Mode = GPIO_MODE_ANALOG;
  GPIO_InitPeripheral(GPIOB, &GPIO_InitStructure);
}




#ifdef USE_FULL_ASSERT


/**
 * @brief Reports the name of the source file and the source line number
 *     where the assert_param error has occurred.
 * @param file pointer to the source file name
 * @param line assert_param error line source number
 */
void assert_failed(const uint8_t* expr, const uint8_t* file, uint32_t line)
{
  /* User can add his own implementation to report the file name and line number,
   ex: printf("Wrong parameters value: file %s on line %d
", file, line) */


  while (1)
  {
  }
}


#endif


/**
 * @}
 */


/**
 * @}
 */


/*************** (C) COPYRIGHT Nations Technologies Inc *****END OF FILE***************/;i++)<>

（左右移動查看全部內容）

此部分不修改

3.2.3 編譯下載

N32WB03xSTB開發板自帶下載器，官方已經配置好了，直接連接Type-C編譯下載

3.1.4 調試驗證

打開串口調試助手，修改相關配置。連接開發板，打印效果如下

此時可以用手指捂住芯片，溫度會升高，也會有相關大小變化

[11:43:40.101]收←◆
this is adc temperature sensor read demo.
ADC temperature sensor: 25.00 C


[11:43:41.134]收←◆ADC temperature sensor: 25.47 C


[11:43:42.161]收←◆ADC temperature sensor: 24.53 C


[11:43:43.189]收←◆ADC temperature sensor: 24.07 C


[11:43:44.218]收←◆ADC temperature sensor: 25.47 C


[11:43:45.244]收←◆ADC temperature sensor: 25.93 C


[11:43:46.271]收←◆ADC temperature sensor: 26.87 C


[11:43:47.299]收←◆ADC temperature sensor: 26.40 C


[11:43:48.326]收←◆ADC temperature sensor: 26.40 C


[11:43:49.352]收←◆ADC temperature sensor: 26.87 C

（左右移動查看全部內容）

C實驗就結束啦！

---

本文由電子發燒友社區發布，轉載請注明以上來源。如需社區合作及入群交流，請?zhí)砑?/span>微信EEFans0806，或者發郵箱liuyong@huaqiu.com。

熱門推薦干貨好文

1、社區精選！PCB多層板設計挑戰賽作品集合

2、開源作品秀，教你如何DIY一款自己的聲源跟蹤小車

3、從零入門物聯網OH開源平臺，從簡單到高階項目，創客、電子愛好者都愛用！

4、低成本ESP32方案，支持OpenHarmony系統開發（附10+項目樣例Demo）

5、從0到1玩轉瑞薩RA4系列開發板，教你變著花樣玩板子

6、四核64位，超強CPU ，看RK3568“競”開發板DEMO！

7、人工智能也能這么玩， 簡單快速入手，還能自定義AI運算

8、全部開源 | 基于全志V85X的運動相機，工業網關，可穿戴式攝像頭

9、高性能雙核RISC-V，滿足大多數開發，這款國產MCU工程師都愛了