msp430f5529產生單路/雙路spwm正弦波信號

//main.c

#include
#include "PWM.h"
#include "include.h"

#define uint unsigned int

/*----------------------------------------------------------------------------------------------
?* 功能：產生單路SPWM波
?* 輸入：無
?* 輸出：P1.4
?*/
void SPWM_1Way_Init(float x,float y)//x控制pwm周期，y控制占空比，y小于1且大于0
{???????????????????????????????????????????????? //X=freg為pwm小周期，y/200為正弦波幅值系數
??? P1SEL |=BIT4;
??? P1DIR |=BIT4;
??? P1DS |=BIT4; //全力驅動
??? P1OUT &=~BIT4;

??? temp1=x;
??? temp1=temp1/100;//變大幅值
??? temp2=temp1*120;//放大倍數
??? temp3=temp2;
??? freg1_4=(int)temp3;//pwm小周期

??? temp5=y;//控制占空比，y小于1
??? spwm_i=0;
??? temp4=Lab1[spwm_i]*temp1*temp5;
??? zhangkong1_4=(int)temp4;
??? temp7=temp1*temp5;
?? ?
??? int i=0;
??? for(i=0;i<)

??? TA0CCR0 =freg1_4;//小PWM 周期
??? TA0CCR3 =zhangkong1_4;//小pwm占空比
??? TA0CCTL3 =OUTMOD_7;//Output mode 7(說明書TA1.1由P1.4輸出pwm)
??? TA0CTL =TASSEL_2+MC_1+ID_0+TACLR;//+TACLR;//選擇時鐘為SMCLK，UP模式

??? P2SEL |=BIT0;
??? P2DIR |=BIT0;
??? P2OUT &=~BIT0;
??? TA1CCR0 =freg1_4;
??? TA1CTL =TASSEL_2+MC_1+ID_0+TACLR;//+TACLR;//選擇時鐘為SMCLK(1.048576MHZ)，UP模式
??? TA1CTL? |= TAIE;//開啟中斷

??? __enable_interrupt();//開啟總中斷
}

/*
?* 功能：輸出兩路SPWM波，相位可調
?* 輸入：無
?* 輸出：P1.4,P1.5
?*/

void SPWM_2Way_Init(float x,float y)
{
??? P1SEL |=BIT4+BIT5;
??? P1DIR |=BIT4+BIT5;
??? P1DS |=BIT4+BIT5;
??? P1OUT &=~BIT4+BIT5;

??? spwm_i=0;
??? spwm_j=28;//控制相位

??? temp1=x;
??? temp1=temp1/100;//變大幅值
??? temp2=temp1*120;//放大倍數
??? temp3=temp2;
??? freg1_4=(int)temp3;//pwm小周期

??? temp5=y;//控制占空比，y小于1
??? temp4=Lab1[spwm_i]*temp1*temp5;
??? zhangkong1_4=(int)temp4;

??? temp6=Lab1[spwm_j]*temp1*temp5;
??? zhangkong1_5=(int)temp6;

??? TA0CCR0 =freg1_4;//小PWM 周期(50=100hz，250=20hz)
??? TA0CCR3 =zhangkong1_4;//小pwm占空比
??? TA0CCR4 =zhangkong1_5;//小pwm占空比
??? TA0CCTL3 =OUTMOD_7;
??? TA0CCTL4 =OUTMOD_7;
??? TA0CTL =TASSEL_2+MC_1+ID_0+TACLR;
??? temp7=temp1*temp5;

??? P2SEL |=BIT0;
??? P2DIR |=BIT0;
??? P2OUT &=~BIT0;

??? TA1CCR0 =freg1_4;//1.04857mhz/(100*100)=2500:100Hz，100個點：10KHZ
??? TA1CTL =TASSEL_2+MC_1+ID_0+TACLR;//選擇時鐘為SMCLK，UP模式
??? TA1CTL? |= TAIE;//開啟中斷

??? __enable_interrupt();//開啟總中斷
}

/*
?* main.c
?*/
int main(void)
{

?? WDTCTL = WDTPW | WDTHOLD;?? ?// stop watchdog timer
?? SPWM_2Way_Init(120,0.4);
}

#if 0
#pragma vector=TIMER1_A1_VECTOR
__interrupt void TimerA1(void)
{
??????? temp4=Lab1[spwm_i++]*temp1*temp5;
??????? zhangkong1_4=(int)temp4;
??????? TA0CCR3 =zhangkong1_4;
??????? if(spwm_i==28)spwm_i=0;
??????? TA1IV=0;??? //GPIO的單獨中斷會自動清零，可TIMER的不會，所以要軟件清零；?。?br />}

#else
#pragma vector=TIMER1_A1_VECTOR
__interrupt void TimerA1(void)
{
??? temp4=Lab1[spwm_i++]*temp7;
??? zhangkong1_4=(int)temp4;
??? TA0CCR3 =zhangkong1_4;
??? if(spwm_i==56)spwm_i=0;

??? temp6=Lab1[spwm_j++]*temp7;
??? zhangkong1_5=(int)temp6;
??? TA0CCR4 =zhangkong1_5;
??? if(spwm_j==56)spwm_j=0;
??? TA1IV=0;??? //GPIO的單獨中斷會自動清零，可TIMER的不會，所以要軟件清零；?。?br />}
#endif

?

?

/*
?* PWM.h
?*/

#ifndef PWM_H_
#define PWM_H_

/*
?* PWM.h
?*/

#ifndef PWM_H_
#define PWM_H_

extern unsigned int spwm_i,spwm_j,load1,load2,load3,load4;
extern int zhangkong1_4;
extern int zhangkong1_5;
extern int freg1_4;
extern int freg1_5;
extern int rang1_4;
extern int rang1_5;
extern float temp1;
extern float temp2;
extern float temp3;
extern float temp4;
extern float temp5;
extern float temp6;
extern float temp7;
extern float temp8;
extern unsigned int Lab_base[];
extern float Lab1[];

extern void SPWM_1Way_Init(float x,float y);
extern void SPWM_2Way_Init(float x,float y);

#endif /* PWM_H_ */

#endif /* PWM_H_ */

?

/*
?* include.h
?*/

#include
#include"PWM.h"

unsigned int spwm_i,spwm_j,load1,load2,load3,load4;
unsigned int freg1_4;
unsigned int freg1_5;
unsigned int zhangkong1_4;
unsigned int zhangkong1_5;
unsigned int rang1_4;
unsigned int rang1_5;
float temp1;
float temp2;
float temp3;
float temp4;
float temp5;
float temp6;
float temp7;
float temp8;

unsigned int Lab_base[]={13,24,36,48,56,69,78,88,94,105,108,111,116,117,118,115,111,106,100,94,86,78,69,57,47,35,24,12,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
floa Lab1[]={13,24,36,48,56,69,78,88,94,105,108,111,116,117,118,115,111,106,100,94,86,78,69,57,47,35,24,12,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
//{117,129,152,160,165,170,175,190,175,165,160,152,129,92,80,68,45,35,12,6,3,0,0,12,18,26,45,56,92,105};