FPGA設計中SPI的參數化結構設計方法

今天給大俠帶來FPGA設計中，對SPI進行參數化結構設計，話不多說，上貨。 ?

為了避免每次SPI驅動重寫，直接參數化，盡量一勞永逸。SPI master有啥用呢，你發現各種外圍芯片的配置一般都是通過SPI配置的，只不過有三線和四線。SPI slave有什么用呢，當外部主機（cpu）要讀取FPGA內部寄存器值，那就很有用了，F(xiàn)PGA寄存器就相當于RAM，cpu通過SPI尋址讀寫數據。代碼僅供參考，勿做商業用途。

SPI salve

SPI salve支持功能：

支持三線SPI或者四線SPI。通過define切換。??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

支持指令長度、幀長自定義。? ??? ? ? ? ? ? ? ? ? ? ? ? ? ?

工作時鐘可自定義，大于SPI clk的2倍。

用戶只需修改：（1）幾線SPI。（2）單幀長度。（3）指令長度。（4）寄存器開辟。

注意：指令最高bit表示讀寫，低寫高讀，其余bit表示地址。指令接著為數據端，兩者位寬之和即為SPI單幀長。

//`define SPI_LINE  //是否是三線SPI
`define SPI_FRAME_WIDTH 16 //SPI一幀長度為16
`define SPI_INS_WIDTH 8    //SPI指令長
`timescale 1ns/1ps
////
module spi_slave 
(
    input     i_clk               , //work clk
    input     i_rst_n             ,  
  
    input     i_spi_clk           , //SPI clk
    input     i_spi_cs            , //SPI cs


    `ifdef SPI_LINE                 //條件編譯
    inout     io_spi_sdio          
    `else
    input     i_spi_mosi          , //SPI mosi
    output    o_spi_miso            //SPI miso
    `endif          
);
//位寬計算函數
function integer clogb2 (input integer depth);
begin
    for (clogb2=0; depth>0; clogb2=clogb2+1) 
        depth = depth >>1;                          
end
endfunction
reg r_cs = 1'b1; //打一拍
always @(posedge i_clk)
begin
    r_cs <= i_spi_cs;
end
reg [1:0] r_spi_clk_edge = 2'b00; //SPI clk邊沿檢測
always @(posedge i_clk)
begin
    r_spi_clk_edge <= {r_spi_clk_edge[0],i_spi_clk};
end //always
reg [clogb2(`SPI_FRAME_WIDTH-1)-1:0] r_spi_cnt = 'd0;
always @(posedge i_clk)
begin
    if (r_cs) //cs為高則歸零
        r_spi_cnt <= 'd0;
    else if (r_spi_clk_edge == 2'b10) //下降沿才計數
        r_spi_cnt <= r_spi_cnt + 'd1;
end
////指令鎖存
reg [`SPI_INS_WIDTH-1:0] r_ins = 'd0;
always @(posedge i_clk)
begin
    if ((~r_cs) && (r_spi_clk_edge == 2'b01)) //上升沿鎖存數據
    begin
        if ((r_spi_cnt >= 0) && (r_spi_cnt <= `SPI_INS_WIDTH-1))
        `ifdef SPI_LINE                 //條件編譯
            r_ins <= {r_ins[`SPI_INS_WIDTH-2:0],io_spi_sdio};  
        `else
            r_ins <= {r_ins[`SPI_INS_WIDTH-2:0],i_spi_mosi};  
        `endif 
    end 
end
////數值寫入
reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_data_rx = 'd0;
always @(posedge i_clk)
begin
    if ((~r_cs) && (r_spi_clk_edge == 2'b01)) //上升沿鎖存數據
    begin
        if (r_spi_cnt >= `SPI_INS_WIDTH)
        `ifdef SPI_LINE
            r_data_rx <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio};
        `else
            r_data_rx <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi};   
        `endif
    end
end
////用戶寄存器定義
reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg0 = 'd0;
reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg1 = 'd0;
reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg2 = 'd0;
reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg3 = 'd0;
////
always @(posedge i_clk,negedge i_rst_n)
begin
    if (~i_rst_n)
    begin
        r_reg0 <= 'd0;
        r_reg1 <= 'd0;
        r_reg2 <= 'd0;
        r_reg3 <= 'd0;


    end
    else if ((~r_ins[`SPI_INS_WIDTH-1]) && (r_spi_cnt == (`SPI_FRAME_WIDTH-1)) && (~r_cs) && (r_spi_clk_edge == 2'b01))
    begin
    `ifdef SPI_LINE
        case (r_ins[`SPI_INS_WIDTH-2:0])
            'd0:begin r_reg0 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end
            'd1:begin r_reg1 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end
            'd2:begin r_reg2 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end
            'd3:begin r_reg3 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end


        endcase 
    `else
        case (r_ins[`SPI_INS_WIDTH-2:0])
            'd0:begin r_reg0 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end
            'd1:begin r_reg1 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end
            'd2:begin r_reg2 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end
            'd3:begin r_reg3 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end


        endcase 
    `endif 
    end


end
////寄存器值讀出
reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_data_tx = 'd0;
always @(posedge i_clk)
begin
    if (r_ins[`SPI_INS_WIDTH-1] && (~r_cs) && (r_spi_clk_edge == 2'b10))
    begin 
        if (r_spi_cnt == (`SPI_INS_WIDTH-1))
        begin
            case (r_ins[`SPI_INS_WIDTH-2:0])
                'd0:begin r_data_tx <= r_reg0; end 
                'd1:begin r_data_tx <= r_reg1; end 
                'd2:begin r_data_tx <= r_reg2; end 
                'd3:begin r_data_tx <= r_reg3; end 
    
            endcase 
        end
        else 
            r_data_tx <= {r_data_tx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],1'b0};
    end 
end


////讀取輸出
`ifdef SPI_LINE
assign io_spi_sdio = (r_ins[`SPI_INS_WIDTH-1]) ? (((r_spi_cnt>=`SPI_INS_WIDTH) && (r_spi_cnt<`SPI_FRAME_WIDTH)) ? r_data_tx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1] : 1'bz) : 1'bz;
`else 
assign o_spi_miso = ((r_spi_cnt>=`SPI_INS_WIDTH) && (r_spi_cnt<`SPI_FRAME_WIDTH)) ? r_data_tx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1] : 1'b0;
`endif


endmodule // end the spi_slave model

SPI master

spi master內部僅僅封裝SPI驅動，寫入值讀出控制由上層控制，這部分邏輯很simple，不贅述。用戶只需給入SPI幀及控制使能即可。

用戶只需修改parameter參數：（1）單幀長；（2）指令長；（3）數據長；（4）工作時鐘；（5）SPI clk。

實現不使用狀態機，采用線性序列計數法。

//`define SPI_LINE  //是否是三線SPI
`timescale 1ns/1ps
module spi_master 
#(parameter p_spi_frame_width = 16, //SPI單幀長度
  parameter p_spi_ins_width = 8   , //指令長度
  parameter p_spi_data_width = 8    //讀出數據長度
 )
(
    input                                i_clk             , //系統時鐘
    input                                i_rst_n           ,
    input                                i_flag            , //檢測到flag的上升沿則啟動一次傳輸,一個時鐘周期即可
   
    input     [p_spi_frame_width-1:0]    i_spi_data        ,
    output                               o_spi_cs          ,
    output                               o_spi_clk         ,


    `ifdef SPI_LINE                 //條件編譯
    inout                                io_spi_sdio       ,          
    `else
    input                                i_spi_miso        , //SPI miso
    output                               o_spi_mosi        , //SPI mosi
    `endif 
    
    output                               o_transfer_done   , //單次傳輸完成
    output    [p_spi_data_width-1:0]     o_spi_data          //讀取數據           
);
parameter p_clk_fre = 200; //XXM時鐘頻率
parameter p_spi_clk_fre = 0.5*1000; //SPI 時鐘速率,表示1M
parameter p_clk_div = p_clk_fre * 1000/p_spi_clk_fre/2-1;
parameter p_spi_cnt_max = p_spi_frame_width*2-1;
parameter p_spi_ins_max = p_spi_ins_width*2-1;
//位寬計算函數
function integer clogb2 (input integer depth);
begin
    for (clogb2=0; depth>0; clogb2=clogb2+1) 
        depth = depth >>1;                          
end
endfunction
//把最大值賦值給線型，直接用p_clk_div仿真有問題，但實際上板是可以的
wire [clogb2(p_clk_div)-1:0] w_clk_div;
assign w_clk_div = p_clk_div;
////時鐘分頻
reg [clogb2(p_clk_div)-1:0] r_cnt_div = 'd0;
always @(posedge i_clk)
begin
    if (r_cnt_div == w_clk_div)
        r_cnt_div <= 'd0;
    else 
        r_cnt_div <= r_cnt_div + 'd1;
end //always
wire w_clk_en; //分頻時鐘使能
assign w_clk_en = (r_cnt_div == w_clk_div) ? 1'b1 : 1'b0;
reg [1:0] r_flag_edge = 2'b00;
reg [clogb2(p_spi_cnt_max)-1:0] r_spi_cnt = 'd0;
always @(posedge i_clk) //flag邊沿檢測
begin
    r_flag_edge <= {r_flag_edge[0],i_flag};
end
//flag信號展寬到低速時鐘域
reg r_flag_enlarge = 1'b0;
always @(posedge i_clk)
begin
    if (r_flag_edge == 2'b01) //上升沿拉高
        r_flag_enlarge <= 1'b1;
    else if (r_spi_cnt == p_spi_ins_max) //足夠長的高電平才拉低
        r_flag_enlarge <= 1'b0;
end
reg [1:0] r_flag_enlarge_edge = 2'b00;
always @(posedge i_clk)
begin
    if (w_clk_en)
        r_flag_enlarge_edge <= {r_flag_enlarge_edge[0],r_flag_enlarge};
end
reg r_cs = 1'b1;
always @(posedge i_clk)
begin
    if (w_clk_en)
    begin
        if (r_flag_enlarge_edge == 2'b01) //檢測到需要進行SPI操作
            r_cs <= 1'b0;
        else if (r_spi_cnt == p_spi_cnt_max) //計數到最大值表示一次SPI完成
            r_cs <= 1'b1;
    end
end
always @(posedge i_clk)
begin
    if (w_clk_en)
    begin
        if(~r_cs) //在操作區間計數
            r_spi_cnt <= r_spi_cnt + 'd1;
        else 
            r_spi_cnt <= 'd0;
    end    
end
////數據傳輸段
reg [p_spi_frame_width-1:0] r_data = 'd0;
always @(posedge i_clk)
begin
    if (w_clk_en)
    begin
        if (r_flag_enlarge_edge == 2'b01) //上升沿刷入
            r_data <= i_spi_data;
        else if (r_spi_cnt[0] == 1'b1) //數據移動
            r_data <= {r_data[p_spi_frame_width-2:0],1'b1};
    end
end
////數據讀取段
reg [p_spi_data_width-1:0] r_data_read = 'd0;
always @(posedge i_clk)
begin
    if (w_clk_en)
    begin
        if (i_spi_data[p_spi_frame_width-1] && (r_spi_cnt > p_spi_ins_max) && (r_spi_cnt[0] == 1'b0)) //是讀
        `ifdef SPI_LINE
            r_data_read <= {r_data_read[p_spi_data_width-2:0],io_spi_sdio};
        `else
            r_data_read <= {r_data_read[p_spi_data_width-2:0],i_spi_miso};
        `endif 
    end    
end
////SPI輸出段
assign o_spi_cs = r_cs;
assign o_spi_clk = r_cs ? 1'b0 : r_spi_cnt[0];
////SPI SDIO的輸入輸出切換
`ifdef SPI_LINE
assign io_spi_sdio = (i_spi_data[p_spi_frame_width-1]) ? (((r_spi_cnt >= 'd0) && (r_spi_cnt <= p_spi_ins_max)) ? r_data[p_spi_frame_width-1] : 1'bz ) : r_data[p_spi_frame_width-1];
`else 
assign o_spi_mosi = r_data[p_spi_frame_width-1];
`endif 
assign o_transfer_done = ((~r_cs) && (r_spi_cnt == p_spi_cnt_max)) ? 1'b1:1'b0;
assign o_spi_data = r_data_read;


endmodule // end the spi_master model

?

?

仿真如下所示：寫入四個寄存器值，再讀出。

仿真代碼如下：

?

?

`define TRANSFER_NUMBER 8 //操作數為4
`define DATA 8'ha5
//`define SPI_LINE
timeunit 1ns;
timeprecision 1ps;
module top;
parameter p_sim_end_time = 1000000; //ns
logic l_clk = 1'b0;
always #2.5 l_clk = ~l_clk;
////復位
logic l_rst_n  = 1'b0;
initial begin
    #100 l_rst_n = 1'b1;
end




wire io_sdio;
wire o_spi_cs;
wire o_spi_clk;
wire o_transfer_done;
wire [7:0] o_spi_data;
////多個數據操作模式
reg r_flag = 1'b0;
reg [1:0] r_first_cnt = 2'b00;
always @(posedge l_clk,negedge l_rst_n)
begin
    if (~l_rst_n)
        r_first_cnt <= 2'b00;
    else if (r_first_cnt == 2'd3)
        r_first_cnt <= r_first_cnt;
    else 
        r_first_cnt <= r_first_cnt + 2'd1;
end
reg [1:0] r_transfer_done_edge = 2'b00;
always @(posedge l_clk)
begin
    r_transfer_done_edge <= {r_transfer_done_edge[0],o_transfer_done};
end
reg [3:0] r_transfer_cnt = 4'd0;
always @(posedge l_clk)
begin
    if ((r_first_cnt == 2'd2) && (r_transfer_cnt < `TRANSFER_NUMBER))
        r_flag <= 1'b1;
    else if ((r_transfer_done_edge == 2'b10) && (r_transfer_cnt < `TRANSFER_NUMBER-1))
        r_flag <= 1'b1;
    else 
        r_flag <= 1'b0;        
end
always @(posedge l_clk)
begin
    if (r_transfer_done_edge == 2'b10)
        r_transfer_cnt <= r_transfer_cnt + 'd1;
end
reg [15:0] r_in_data  = 16'd0;
always @(*)
begin
    if (~l_rst_n) //仿真不執行此段仿真會有問題
        r_in_data  = 16'h0000;
    else 
    begin 
    case(r_transfer_cnt)
        4'd0:begin  r_in_data  = {8'h00,8'h43}; end 
        4'd1:begin  r_in_data  = 16'h0132; end 
        4'd2:begin  r_in_data  = 16'h0245; end 
        4'd3:begin  r_in_data  = 16'h0367; end 
        4'd4:begin  r_in_data  = 16'h8000; end 
        4'd5:begin  r_in_data  = 16'h8100; end 
        4'd6:begin  r_in_data  = 16'h8200; end 
        4'd7:begin  r_in_data  = 16'h8300; end 


        default:begin  r_in_data  = 16'h0000; end
    endcase
    end 
end


wire w_spi_miso;
wire w_spi_mosi;


spi_master inst_spi_master (
    .i_clk             (l_clk),
    .i_rst_n           (),
    .i_flag            (r_flag),
    .i_spi_data        (r_in_data),
    .o_spi_cs          (o_spi_cs),
    .o_spi_clk         (o_spi_clk),
    `ifdef SPI_LINE
    .io_spi_sdio       (io_sdio),
    `else
    .i_spi_miso        (w_spi_miso),
    .o_spi_mosi        (w_spi_mosi),
    `endif
    .o_transfer_done   (o_transfer_done),
    .o_spi_data        (o_spi_data)
    
);


spi_slave  inst_spi_slave (
    .i_clk                            (l_clk),
    .i_rst_n                          (l_rst_n),


    .i_spi_clk                        (o_spi_clk),
    .i_spi_cs                         (o_spi_cs),
    `ifdef SPI_LINE
    .io_spi_sdio                      (io_sdio)
    `else
    .i_spi_mosi                      (w_spi_mosi),
    .o_spi_miso                      (w_spi_miso)
    `endif


);


initial begin
    #p_sim_end_time $stop;
end


    
endmodule

三線SPI：

四線SPI：

?

可以看到讀寫是一致的，驗證通過。

審核編輯：黃飛

?