資料介紹
The attenuation setting in the AD8321 is determined by the 8-bit word in the data latch. The SDATA load sequence is initiated by a falling edge on DATEN. The gain control data (SDATA) is serially loaded (MSB first) into the 7-bit shift register at each rising edge of the clock. See Figure 24. While DATEN is low, the data latch holds the previous data word allowing the attenuation level to remain unchanged. After eight clock cycles the new data word is fully loaded and DATEN is switched high. This enables the data latch and the loaded register data is passed to the attenuator with the updated gain value. Also at this DATEN transition, the internal clock is disabled, thus inhibiting new serial input data.
The power amplifier has two basic modes of operation. A forward mode (or power-up mode) and a reverse mode (or power-down) mode. In the power-up mode (PD = 1), the power amplifier stage is enabled and the AD8321 has a maximum gain of 20 V/V or 26 dB (into 75 W). With a total attenuation of
53.43 dB in the DAC, vernier and preamp, the AD8321’s total gain range is 26 dB to –27.43 dB. In both the forward or reverse mode the single-ended output signal maintains a dc level of VCC/2. This dc output level provides for optimum large signal linearity.
In the power-down mode (PD = 0), the power amplifier is turned off and a “reverse” amplifier (the inner triangle in Figure 22) is enabled. During this 1-to-0 transition, the output power is disabled. This assures that S11 and S22 remain approximately equal to zero thus minimizing line reflections. In the time domain, as PD switches states, a transitional glitch and pedestal offset results (See Figures 14 and 15). These anomalies have been minimized by temperature compensated internal circuitry and laser trimming. The powered down supply current drops to 52 mA versus 90 mA in the power-up mode.
The power amplifier has two basic modes of operation. A forward mode (or power-up mode) and a reverse mode (or power-down) mode. In the power-up mode (PD = 1), the power amplifier stage is enabled and the AD8321 has a maximum gain of 20 V/V or 26 dB (into 75 W). With a total attenuation of
53.43 dB in the DAC, vernier and preamp, the AD8321’s total gain range is 26 dB to –27.43 dB. In both the forward or reverse mode the single-ended output signal maintains a dc level of VCC/2. This dc output level provides for optimum large signal linearity.
In the power-down mode (PD = 0), the power amplifier is turned off and a “reverse” amplifier (the inner triangle in Figure 22) is enabled. During this 1-to-0 transition, the output power is disabled. This assures that S11 and S22 remain approximately equal to zero thus minimizing line reflections. In the time domain, as PD switches states, a transitional glitch and pedestal offset results (See Figures 14 and 15). These anomalies have been minimized by temperature compensated internal circuitry and laser trimming. The powered down supply current drops to 52 mA versus 90 mA in the power-up mode.
下載該資料的人也在下載
下載該資料的人還在閱讀
更多 >
- AD8321:Gain程序變量CATV線驅動數據Sheet
- NCP5030 pdf ,datasheet
- RT9505 datasheet,pdf資料(Linear
- RT9503 datasheet,pdf資料(Fully I
- RT9502 datasheet,pdf資料(Linear
- BGY885A datasheet,pdf(860 MHz,
- AIC1790 datasheet,pdf(1 Cell L
- C1165/C1205,pdf datasheet (Sin
- ad522,pdf datasheet
- mtk1389 pdf datasheet
- RCA-00-A pdf datasheet
- A7533 pdf datasheet
- TA7302 pdf datasheet
- tlv5619 pdf datasheet
- 2N5639 pdf datasheet
- Li-ion/Polymer二次電池的應用方案 200次閱讀
- EPCM3568A-LI屏幕分辨率和開機logo設置 275次閱讀
- 什么是Li-Fi?Li-Fi的工作原理和應用領域 1152次閱讀
- 深度解析MD-3568LI工控板 541次閱讀
- CATV中dBm,dBmV和dBμV的轉換 3361次閱讀
- 用于75Ω測量的CATV最小損耗衰減器 1480次閱讀
- 表征與電量計一起使用的Li+電池 1027次閱讀
- 擴展MAX9930在CATV應用的功能 848次閱讀
- 簡化1節Li+電池供電設備的設計 932次閱讀
- 簡化1節Li+電池供電器件的設計 900次閱讀
- 分享一個快速閱讀datasheet的方法 2311次閱讀
- 如何通過提高效率來提高CATV放大器的下行帶寬和上行容量 2388次閱讀
- 一文讀懂Li-Fi概念 1327次閱讀
- AD9如何簡單快速的制作出原理圖符號 7441次閱讀
- Li-Fi的含義、與Wi-Fi的不同以及其優勢 8106次閱讀
下載排行
本周
- 1ADE-12H混頻器規格書
- 0.28 MB | 1次下載 | 5 積分
- 2AD9984A高性能10位顯示接口英文手冊
- 0.49 MB | 1次下載 | 5 積分
- 351開發板芯片資料
- 14.95 MB | 1次下載 | 1 積分
- 4用TL431LI-Q1監控電流供應
- 176.71KB | 1次下載 | 免費
- 5十進制數據轉十六進制字符_轉ASCII碼
- 0.01 MB | 次下載 | 免費
- 6使用TRF7970A進行NFC主動和被動點對點通信
- 926.87KB | 次下載 | 免費
- 7LP8864-Q1 LP8864S-Q1 LP8866-Q1和LP8866S-Q1診斷說明和故障處理程序
- 577.42KB | 次下載 | 免費
- 8將設計移植到LP3470A低lq電壓監控器,以改善電源監控
- 115.28KB | 次下載 | 免費
本月
- 1HFSS電磁仿真設計應用詳解PDF電子教程免費下載
- 24.30 MB | 129次下載 | 1 積分
- 2正激、反激、推挽、全橋、半橋區別和特點
- 0.91 MB | 36次下載 | 1 積分
- 3GBT 4706.1-2024家用和類似用途電器的安全第1部分:通用要求
- 7.43 MB | 20次下載 | 免費
- 4在設計中使用MOSFET瞬態熱阻抗曲線
- 1.57MB | 15次下載 | 免費
- 5幾張電動車充電器電路圖
- 0.23 MB | 9次下載 | 1 積分
- 6AD18學習筆記
- 14.47 MB | 8次下載 | 2 積分
- 7H橋中的電流感測
- 545.39KB | 7次下載 | 免費
- 8電機驅動器電路板布局的最佳實踐
- 3.03MB | 6次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935113次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420061次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233084次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191360次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183329次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81578次下載 | 10 積分
- 7Keil工具MDK-Arm免費下載
- 0.02 MB | 73804次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65985次下載 | 10 積分
評論