資料介紹
Over the past five years, the development of true analog CMOS processes
has led to the use of high-speed analog devices in the digital arena.
System speeds of 150 MHz and higher have become common for digital
logic. Systems that were considered high end and high speed a few years
ago are now cheaply and easily implemented. However, this integration
of fast system speeds brings with it the challenges of analog system
design to a digital world. This document is a guideline for printed circuit
board (PCB) layouts and designs associated with high-speed systems.
“High speed” does not just mean faster communication rates (e.g., faster
than 1 gigabit per second (Gbps)). A transistor-transistor logic (TTL)
signal with a 600-ps rise time is also considered a high-speed signal. This
opens up the entire PCB to careful and targeted board simulation and
design. The designer must consider any discontinuities on the board. The
“Time-Domain Reflectometry” and “Discontinuity” sections explain how
to eliminate discontinuities on a PCB. Some sources of discontinuities are
vias, right angled bends, and passive connectors.
The “Termination” section explains about terminations for signals on
PCBs. The placement and selection of termination resistors are critical in
order to avoid reflections.
As systems require higher speeds, they use differential signals instead of
single-ended signals because of better noise margins and immunity.
Differential signals require special attention from PCB designers with
regards to trace layout. The “Trace Layout” section addresses differential
traces in terms of trace layout. Crosstalk, which can adversely affect
single ended and differential signals alike, is also addressed in this
section.
All the dense, high-speed switching (i.e., hundreds of I/O pins switching
at rates faster than 500-ps rise and fall times) produces powerful transient
changes in power supply voltage. These transient changes occur because
a signal switching at higher frequency consumes a proportionally greater
amount of power than a signal switching at a lower frequency. As a
result, a device does not have a stable power reference that both analog
and digital circuits can derive their power from. This phenomenon is
called simultaneous switching noise (SSN). The “Dielectric Material”
section discusses how to eliminate some of these SSN problems through
careful board design.
has led to the use of high-speed analog devices in the digital arena.
System speeds of 150 MHz and higher have become common for digital
logic. Systems that were considered high end and high speed a few years
ago are now cheaply and easily implemented. However, this integration
of fast system speeds brings with it the challenges of analog system
design to a digital world. This document is a guideline for printed circuit
board (PCB) layouts and designs associated with high-speed systems.
“High speed” does not just mean faster communication rates (e.g., faster
than 1 gigabit per second (Gbps)). A transistor-transistor logic (TTL)
signal with a 600-ps rise time is also considered a high-speed signal. This
opens up the entire PCB to careful and targeted board simulation and
design. The designer must consider any discontinuities on the board. The
“Time-Domain Reflectometry” and “Discontinuity” sections explain how
to eliminate discontinuities on a PCB. Some sources of discontinuities are
vias, right angled bends, and passive connectors.
The “Termination” section explains about terminations for signals on
PCBs. The placement and selection of termination resistors are critical in
order to avoid reflections.
As systems require higher speeds, they use differential signals instead of
single-ended signals because of better noise margins and immunity.
Differential signals require special attention from PCB designers with
regards to trace layout. The “Trace Layout” section addresses differential
traces in terms of trace layout. Crosstalk, which can adversely affect
single ended and differential signals alike, is also addressed in this
section.
All the dense, high-speed switching (i.e., hundreds of I/O pins switching
at rates faster than 500-ps rise and fall times) produces powerful transient
changes in power supply voltage. These transient changes occur because
a signal switching at higher frequency consumes a proportionally greater
amount of power than a signal switching at a lower frequency. As a
result, a device does not have a stable power reference that both analog
and digital circuits can derive their power from. This phenomenon is
called simultaneous switching noise (SSN). The “Dielectric Material”
section discusses how to eliminate some of these SSN problems through
careful board design.
下載該資料的人也在下載
下載該資料的人還在閱讀
更多 >
- Designing with a New Super Fast 0次下載
- Designing High Speed Active Filt 0次下載
- 為您的FPGA選擇合適的電源 59次下載
- OPA561,pdf(High-Current, High-
- Guidelines for Completion of a
- 高功率高亮度LED驅動器,Driving high powe
- Designing High-Performance DSP
- Designing auto power systems w
- Designing a High Performance S
- Designing a 33MHz, 32-Bit PCI
- Designing a High Performance S
- Designing a 33MHz, 32-Bit PCI
- Designing with 1.5-V Devices
- Ground and VCC Bounce of High-
- Measurement guidelines for DVB
- DPHY在high-speed模式下有雙向傳輸?shù)墓δ軉幔?/a> 420次閱讀
- 什么是閾值、上拉電阻和下拉電阻、負載電流? 1283次閱讀
- 如何創建一個high-level和object-oriented的模型 341次閱讀
- SiamRPN:High Performance Visual Tracking with Siamese Region Proposal Network 孿生網絡 941次閱讀
- 幾種檢查代碼質量的利器介紹 1212次閱讀
- 一個由探測線圈和反相器構成振蕩器的選頻模塊 1575次閱讀
- 寬禁帶器件和仿真環境介紹 1457次閱讀
- 在貼片加工廠中有哪些安全防護需要了解 1306次閱讀
- 復合放大器實現高精度的高輸出驅動能力 獲得最佳的性能 1600次閱讀
- 用降壓型穩壓器或線性穩壓器電源時值來會為負載供電 984次閱讀
- 鋰電池并聯充電時保護板均衡原理 3w次閱讀
- 更小更智能的電機控制器推進HEV/EV市場 1105次閱讀
- 如何理解ARM異常、中斷和向量表 4171次閱讀
- I2C基本的傳輸方式知識整理 2w次閱讀
- 以i.MX6UL為例為大家介紹上電時序的設計 2w次閱讀
下載排行
本周
- 1FS4059C帶NTC升壓型三節鋰電池充電管理IC數據手冊
- 3.53 MB | 3次下載 | 免費
- 216位數字輸出型環境光強度傳感器集成電路bh1750FVI中文數據手冊
- 2.67 MB | 1次下載 | 免費
- 3MCx8316x 在掃地機器人中的應用
- 1.34MB | 1次下載 | 免費
- 4掃地機器人中的霍爾效應傳感器應用說明
- 666.09KB | 1次下載 | 免費
- 5如何調整模擬前端信號鏈的 S 參數
- 794.19KB | 1次下載 | 免費
- 6FS4059B帶NTC升壓型兩節鋰電池充電管理IC數據手冊
- 3.24 MB | 1次下載 | 免費
- 7基于波形捕獲的超聲波傳感水流量計量技術應用說明
- 1.01MB | 1次下載 | 免費
- 8使用反相降壓/升壓轉換器應用說明
- 996.8KB | 次下載 | 免費
本月
- 1HFSS電磁仿真設計應用詳解PDF電子教程免費下載
- 24.30 MB | 129次下載 | 1 積分
- 2繼電保護原理
- 2.80 MB | 40次下載 | 免費
- 3正激、反激、推挽、全橋、半橋區別和特點
- 0.91 MB | 34次下載 | 1 積分
- 4labview實現DBC在界面加載配置
- 0.57 MB | 24次下載 | 5 積分
- 5在設計中使用MOSFET瞬態熱阻抗曲線
- 1.57MB | 15次下載 | 免費
- 6GBT 4706.1-2024家用和類似用途電器的安全第1部分:通用要求
- 7.43 MB | 14次下載 | 免費
- 7AD18學習筆記
- 14.47 MB | 8次下載 | 2 積分
- 8H橋中的電流感測
- 545.39KB | 7次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935113次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420061次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233084次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191360次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183329次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81578次下載 | 10 積分
- 7Keil工具M(jìn)DK-Arm免費下載
- 0.02 MB | 73804次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65985次下載 | 10 積分
評論
查看更多