資料介紹
Table of Contents
CN0376 Evaluation Board Guide
Overview
CN0376 is a dual-channel, channel-to-channel isolated, thermocouple or RTD input suitable for programmable logic controllers (PLC) and distributed control systems (DCS). Each channel can accept either a thermocouple or a RTD input. The entire circuit is powered from a standard 24 V bus supply.
The AD7124-4 24-bit, Σ-Δ ADC with programmable gain array (PGA) and voltage reference provides the complete set of features to implement a flexible input capable of connection to either thermocouple or RTD sensors. Features include on-chip reference, PGA, excitation currents, bias voltage generator, and flexible filtering with enhanced 50 Hz and 60 Hz rejection options. The AD7124-4 is in a small 5 mm × 5 mm LFCSP package, making it ideal in channel-to-channel isolated designs where space is a premium. It also includes multiple diagnostic functions that are available to the user. The ADuM5010 isolated dc-to-dc converter provides 3.3 V isolated power via integrated isoPower? technology. The ADuM1441 isolates the serial peripheral interface (SPI) for the AD7124-4. The ADuM1441 micropower isolator consumes only 4.8 μA per channel when idle, resulting in an energy efficient solution. The ADP2441 36 V, step-down, dc-to-dc regulator accepts an industrial standard 24 V supply, with wide tolerance on the input voltage and steps it down to 5V to be used by the system.
THe EVAL-CN0376-SDPZ evaluation connects to ADI's System Demonstration Platform(SDP) and also features PMOD-compatible headers for interfacing with other development platforms.
Required Equipment
- EVAL-SDP-CB1Z Controller Board (SDP-B Board)
- DC Power Supply (+12V to +24V)
- RTD (PT100 or PT1000)
- Thermocouple
- PC with the following Minimum Requirements
- Windows Vista/7 (32-bit)
- USB type A Port
- Processor rated at 1GHz or faster
- 1GB RAM and 500 MB available hard disk space
- USB type A to USB type mini-B cable
General Setup
- The EVAL-CN0376-SDPZ (CN-0376 Board) connects to the EVAL-SDP-CB1Z (SDP-B Board) via the 120-Pin connector
- The EVAL-SDP-CB1Z (SDP-B Board) connects to the PC via the USB cable.
- Header P4 is a PMOD compatible SPI header for communication to Channel 1
- Header P5 is a PMOD compatible SPI header for communication to Channel 2
- Header PWR_SEL is used for selecting the power source of the system using a jumper (Terminal Block P3 or PMOD)
- Terminal block P3 is the power supply input (input range:+5.5V to +36V DC)
- Terminal block P1 is the sensor input (RTD or Thermocouple) for Channel 1
- Terminal block P2 is the sensor input (RTD or Thermocouple) for Channel 2
Sensor Connection
2-Wire RTD
- Connect RTD to AIN+ and AIN- terminals
- Short terminals IEXC and AIN+
- Short terminals RETURN and AIN-
3-Wire RTD
- Connect RTD wires to AIN+, AIN- and RETURN termnials
- Short terminals IEXC and AIN+
4-Wire RTD
- Connect RTD to IEXC, AIN+, AIN- and RETURN terminals
Thermocoupe
- Connect Thermocouple to AIN+ and AIN- terminals
Power Options
Jumper Positon EXT
- System is powered using termnial block P3 (input range:+5.5V to +36V DC)
- When no supply is present on P3, the system draws power from USB when using the SDP
Jumper Positon PMOD
- System is powered using the PMOD headers (+3.3V DC)
Installing the Evaluation Software
- Extract the file CN0376_Evaluation_Software.zip and open the file setup.exe.
NOTE: It is recommended that you install the CN-0376 Evaluation Software to the default directory path C:/Program Files/Analog Devices/CN0376/ and all National Instruments products to C:/Program Files/National Instruments/
- Click Next to view the installation review page
}}
- Click Next to start the installation
- Upon completion of the installation of the CN-0376 Evaluation Software, the installer for the ADI SDP Drivers will execute.
NOTE: It is recommended that you close all other applications before clicking “Next”. This will make it possible to update relevant system files without having to reboot your computer.
- Press “Next” to set the installation location for the SDP Drivers.
It is recommended that you install the drivers to the default directory path
C:/Program Files/Analog Devices/SDP/Drivers
- Press “Next” to install the SDP Drivers and complete the installation of all software. Click “Finish” when done.
Using the Evaluation Software
Software Control and Indicator Descriptions
Main Tab
- Run/Stop
- Start/Stop data acquisition from the evaluation board
- Clear Data
- Clear the data on the chart and on voltage/current indicators
- Save Data
- Save the data collected to a tab delimited ASCII spreadsheet file
- Reset
- Reset the evaluation board and software to the defualt startup configuration
- Channel 1 Temperature Display
- Displays the temperature reading from Channel 1 ( in Degrees Celsius)
- Channel 1 RTD Resistance/TC Voltage Display
- Displays the equivalent RTD Resistance of Channel 1 when in RTD Mode
- Displays the Thermocouple voltage of Channel 1 when in Thermocouple Mode
- Channel 2 Temperature Display
- Displays the temperature reading from Channel 2 ( in Degrees Celsius)
- Channel 2 RTD Resistance/TC Voltage Display
- Displays the equivalent RTD Resistance of Channel 2 when in RTD Mode
- Displays the Thermocouple voltage of Channel 2 when in Thermocouple Mode
- Cold Junction Compensation Information
- Displays the Temperature and Resistance of the CJC Thermistor of both Channel 1 and 2 when in Thermocouple Mode
- Display Units
- Temperature- data on the chart is displayed as degrees Celsius
- ADC Code - data on the chart is displayed as ADC codes
- Chart
- Data plot for the data acquisition (may be displayed as voltage/current value or ADC code)
- Status Bar
- Displays a message to the user detailing the current state of the software There are three status LED colors:
Inactive
Busy
Error
Histogram Tab
User needs to sample data first using Run to get histogram data on this page.
- Select Channel
- Channel selection for Histogram display
- Get Histogram
- Analyzes the data from the selected channel and displays the histogram data
- Maximum Code
- Display for the highest code from the sampled data of the selected channel
- Minimum Code
- Display for the lowest code from the sampled data of the selected channel
- Code Spread
- Display for the difference between the highest and lowest code from the sampled data of the selected channel
- Peak-to-Peak Resolution
- Display for computed Peak-to-Peak Resolution(bits) of the selected channel
- Histogram Graph
- Plot for the histogram data
Configuration Tab
Allows for ADC configuration of either channel
Input Type
- PT100 - activates the Excitation current source and configures the ADC to read from PT100 RTD
- PT1000 - activates the Excitation current source and configures the ADC to read from PT1000 RTD
- Thermocouple - activates the TC bias,CJC, and configures the ADC to read from thermocouple
RTD Connection
- 2-Wire - Excitation current available at IEXC pin. Short IEXC and AIN+ pins. Short AIN- and RETURN pins.
- 3-Wire - Matched Excitation currents available at IEXC and AIN- pins
- 4-Wire - Excitation current available at IEXC pin. Short IEXC and AIN+ pins.
Power Mode - Select Power Mode of the ADC. This affects power consumption and ADC data rate. Please consult [ADI>AD7124-4] datasheet for more information
Filter Type - Select the digital filter used for the ADC conversion. Please consult [ADI>AD7124-4] datasheet for more information
Post Filter - Select the data rate when the Post Filter are used
Sampling Rate - Slider control to change the ADC data rate. The numerical display shows the corresponding data rate. This is dependent on the power mode and filter type
Enabled/Disabled - Toggle to enable or disable the corresponding channel
Configure - Press this button to apply the configurations to the corresponding channel
Advanced Configuration Tab
Allows control of Excitation Current, Burnout Current, PGA Gain and for enabling ADC Error Checks
Error Flags Tab
ADC Error Indicators. Please consult [ADI>AD7124-4] datasheet for information regarding the ADC Errors
Running the System
- Open the CN0376.exe application from the default installation location.
- The software will connect to the board automatically.
- Click the Run Button
- Click the Stop Button when acquisition is complete.
Saving Data to a Spreadsheet File
- Click the Save Data Button.
- Browse to the directory location where the spreadsheet file is to be saved.
- Name the file.
- Click the OK Button.
The software saves the spreadsheet file as ASCII text with columns separated by tabs
More Information and Useful Links
- 兆易創新GD32C10x系列開發板例程及評估板用戶指南
- 兆易創新GD32C11x系列開發板例程及評估板用戶指南
- 基于CN-0376溫度量測的參考設計
- CN0376設計與集成文件
- CN0364評估板和軟件用戶指南
- CN0370評估板和軟件用戶指南
- CN0372評估板和軟件用戶指南
- CN0385評估板和軟件用戶指南
- CN0376設計與集成文件
- CN0240評估板指南
- CN0254評估板指南
- CN0263評估板指南
- CN-0376:適合PLC/DCS應用的通道間隔離溫度輸入(熱電偶/RTD)
- MCP9600基礎知識及評估板用戶指南
- MCP3903評估板用戶指南
- 迅為RK3568開發板驅動開發指南-輸入子系統 575次閱讀
- RZ/G2L開發板使用指南(上) 873次閱讀
- 如何在RZ/V2L評估板套件上使用AI SDK 768次閱讀
- 基于CW32L083評估板的簡易低功耗功能測試 666次閱讀
- 高頻放大器評估板 620次閱讀
- 系統演示平臺簡化了從評估到原型設計的過渡 646次閱讀
- 為MAX7651評估板配置Keil μVision IDE 1029次閱讀
- 自制低成本開發板/評估板學習教程 1329次閱讀
- CPK-RA6M4評估板入門指南(六) 2169次閱讀
- CPK-RA6M4評估板入門指南(五) 2256次閱讀
- CPK-RA6M4評估板入門指南(四) 1236次閱讀
- CPK-RA6M4評估板入門指南(一) 1355次閱讀
- 米爾科技 Beetle IoT 評估板概述 1189次閱讀
- 電子印刷電路板初步設計和開發階段的指南 5830次閱讀
- 帶電池短路保護的一款可靠復合視頻傳輸解決方案 2355次閱讀
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論
查看更多