資料介紹
Table of Contents
CN0348 Software User Guide
Overview
CN-0348 showcases a solution for precision 16-bit digital-to-analog conversion with wide dynamic signal range in a single supply system. It utilizes a 5V voltage reference (ADR4550), a voltage output digital-to-analog converter (AD5541A), and a rail-rail amplifier as the output buffer (ADA4500-2). The ADA4500-2 exhibits zero crossover distortion and this feature makes it an excellent choice as an output buffer to maintain the linearity of the AD5541A over its input digital code and provide a wide dynamic output range. The combination of parts provides industry-leading 16-bit integral nonlinearity (INL) of ±1LSB and differential nonlinearity (DNL) of ±1LSB with guaranteed monotonicity. This user guide gives information on how to use the evaluation software to collect data from the EVAL-CN0348-SDPZ Daughter Board.
Required Equipment
- EVAL-SDP-CB1Z Controller Board (SDP-B Board)
- EVAL-CN0348-SDPZ Evaluation Board (CN-0348 Board)
-
- (supplied with provided CD in kit)
- PC with the following Minimum Requirements
- Windows XP SP2, Windows Vista or Windows 7
- USB type A Port
- Processor rated at 1GHz or faster
- USB type A to USB type mini-B cable
- SMB Connector
- For INL/DNL data collection:
- GPIB Controller for Hi-Speed USB Type A Connector Cable (NI-488.2 3.1.1 GPIB controller driver is available at https://www.ni.com/en-us/support/model.gpib-usb-hs.html
- Agilent 3458A
NOTE - Any multimeter can be used with this board. However, for INL/DNL measurement, software interface was written with the Agilent 3458A in mind.
Installing the Software
- Open the file setup.exe that is provided from the CD in kit.
NOTE: It is recommended that you install the CN0348 Evaluation Software to the default directory path C:/Program Files/Analog Devices/CN0348/ and all National Instruments products to C:/Program Files/National Instruments/
- Click Next to view the installation review page
- Click Next to start the installation
- Upon completion of the installation of the CN0348 SDP Evaluation Software, the installer for the ADI SDP Drivers will execute.
NOTE: It is recommended that you close all other applications before clicking “Next”. This will make it possible to update relevant system files without having to reboot your computer.
- Click “Next” to set the installation location for the SDP Drivers.
It is recommended that you install the drivers to the default directory path
C:/Program Files/Analog Devices/SDP/DriversR2
- Click “Next” to install the SDP Drivers and complete the installation of all software.
Using the Evaluation Software
Software Control and Indicator Descriptions
- LDAC COntrol
- Always check the box before starting any test
- Write to DAC Button
- Enter the digital input code in “DIN”
- When “WRITE TO DAC” button is clicked, the digital input code is sent to the DAC
- Output Indicator
- The LED string indicates the digital input code being written to the DAC (from bit 15 to bit 0)
- System Status String / LED Indicator
- The string indicator displays a message to the user detailing the current state of the software
- The LED indicator displays the current state of the software in the form of an LED. There are three status LED colors
Inactive
Busy
Error
- Code Step Control
- Enter the code step between each digital input to be written to the DAC
- Agilent 3458A GPIB Address Control
- Enter in the GPIB address of the multimeter
- GPIB Address can be determined from the multimeter by manually pressing down on SHIFT+Local. By default it should be 22
- Current Code / Voltage Indicator
- This indicates the current digital input code and output voltage of the DAC
- File Directory Control
- This allows you to enter the file directory and name to save the INL/DNL measurement data
- INL / DNL measurement graphs
- These graphs display the INL and DNL vs. input digital code when data collection is done
- Transfer Function Graph
- This graph shows the transfer function of the DAC output voltage vs. input digital code
- SDP Board Firmware Information
- This gives you the up to date information on the SDP board firmware
Connecting the Hardware and Taking Measurements
- Connect the SDP Board to the CN0348 Board
- Connect +6V and analog ground to the CN0348 board (J1)
- Connect the USB cable supplied with the SDP board to the USB port on the PC and the SDP board
- Connect Vout (J3) to a multimeter
- Open CN0348.exe. It should be located in C:/Program Files/Analog Devices/CN0348/
- The application will attempt to connect to the board immediately
- Check LDAC box
- Perform functionality test by entering the following in DIN and click WRITE TO DAC
- 0000; multimeter should read close to 0V
- FFFF; multimeter should read close to 5V
- OUTPUT (Bit 15 to Bit 0) should also light up the associated LED indicator
For INL/DNL data collection:
- Connect Vout to the Agilent 3458A multimeter
- Connect the Agilent 3458A to the PC using a GPIB to USB Type A connector (for data collection via Labview software)
- Set the multimeter to have “NPLC” as 1
- Enter GPIB Address of Agilent 3458A.
- Enter desired Code Step
- Code Step = 16 takes about 4min 10sec to finish measurement
- Code Step = 32 takes about 2min 5sec to finish measurement
- Enter the file name and path you want to save data in Enter file name to save data before running
- Click on Start
- Current Code and Current voltage should show the progress of measurements
- To exit, go to File > Exit.
- CN0335軟件用戶指南
- CN0336軟件用戶指南
- CN0349軟件用戶指南
- CN0350軟件用戶指南
- CN-0354軟件用戶指南
- CN0355軟件用戶指南
- CN0196軟件用戶指南
- CN0203軟件用戶指南
- CN0204軟件用戶指南
- CN0218軟件用戶指南
- CN-0269軟件用戶指南
- CN-0271軟件用戶指南
- CN-0288軟件用戶指南
- CN-0296軟件用戶指南
- CN-0301軟件用戶指南
- 上位機軟件的用戶界面設計技巧 773次閱讀
- 搞不懂組態軟件和HMI?常見組態軟件有哪些? 4789次閱讀
- 常用的遠程控制軟件介紹 1763次閱讀
- 醫療器械軟件風險分析介紹 醫療設備軟件靜態和動態分析技巧 1850次閱讀
- 如何使用openEuler用戶軟件倉(EUR) 1223次閱讀
- 基于STM32 MCU應用的EMC指南之軟件篇 1020次閱讀
- 開源、可重用的軟件堆棧支持CbM的實時處理和算法開發 900次閱讀
- EsDA為用戶帶來簡單易用的軟件設計體驗 1884次閱讀
- 使用含快速開關SiC器件的RC緩沖電路實用解決方案和指南 2531次閱讀
- 常見的組態軟件有哪些 1.2w次閱讀
- 如何正確的設置IAR單片機編程軟件 4994次閱讀
- 一款以BitTorrent代幣連接和獎勵用戶的軟件BitTorrent Speed介紹 3328次閱讀
- 組態軟件的特點和應用 1.4w次閱讀
- 組態軟件是什么_組態軟件有什么用 3.5w次閱讀
- 長虹CN-7機芯彩電場掃描電路分析 1w次閱讀
下載排行
本周
- 1HFSS電磁仿真設計應用詳解PDF電子教程免費下載
- 24.30 MB | 128次下載 | 1 積分
- 2雷達的基本分類方法
- 1.25 MB | 4次下載 | 4 積分
- 3電感技術講解
- 827.73 KB | 2次下載 | 免費
- 4從 MSP430? MCU 到 MSPM0 MCU 的遷移指南
- 1.17MB | 2次下載 | 免費
- 5有源低通濾波器設計應用說明
- 1.12MB | 2次下載 | 免費
- 6RA-Eco-RA2E1-48PIN-V1.0開發板資料
- 35.59 MB | 2次下載 | 免費
- 7面向熱插拔應用的 I2C 解決方案
- 685.57KB | 1次下載 | 免費
- 8愛普生有源晶體振蕩器SG3225EEN應用于儲能NPC、新能源
- 317.46 KB | 1次下載 | 免費
本月
- 12024年工控與通信行業上游發展趨勢和熱點解讀
- 2.61 MB | 763次下載 | 免費
- 2HFSS電磁仿真設計應用詳解PDF電子教程免費下載
- 24.30 MB | 128次下載 | 1 積分
- 3繼電保護原理
- 2.80 MB | 36次下載 | 免費
- 4正激、反激、推挽、全橋、半橋區別和特點
- 0.91 MB | 32次下載 | 1 積分
- 5labview實現DBC在界面加載配置
- 0.57 MB | 21次下載 | 5 積分
- 6在設計中使用MOSFET瞬態熱阻抗曲線
- 1.57MB | 15次下載 | 免費
- 7GBT 4706.1-2024家用和類似用途電器的安全第1部分:通用要求
- 7.43 MB | 14次下載 | 免費
- 8AD18學習筆記
- 14.47 MB | 8次下載 | 2 積分
總榜
- 1matlab軟件下載入口
- 未知 | 935113次下載 | 10 積分
- 2開源硬件-PMP21529.1-4 開關降壓/升壓雙向直流/直流轉換器 PCB layout 設計
- 1.48MB | 420061次下載 | 10 積分
- 3Altium DXP2002下載入口
- 未知 | 233084次下載 | 10 積分
- 4電路仿真軟件multisim 10.0免費下載
- 340992 | 191360次下載 | 10 積分
- 5十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183329次下載 | 10 積分
- 6labview8.5下載
- 未知 | 81578次下載 | 10 積分
- 7Keil工具M(jìn)DK-Arm免費下載
- 0.02 MB | 73804次下載 | 10 積分
- 8LabVIEW 8.6下載
- 未知 | 65985次下載 | 10 積分
評論
查看更多