資料介紹
Table of Contents
AD9739A Evaluation Board, DAC-FMC Interposer & Xilinx Reference Design
Introduction
The AD9739A is a 14-bit, 2.5GSPS high performance RF digital-to-analog converter (DAC) capable of synthesizing wideband signals from DC up to 3 GHz. This reference design includes a DDS generator that drives both ports of the device. The programming is done via the USB-SPI interface.
Supported Devices
Supported Carriers
Quick Start Guide
The bit file provided combines the FPGA bit file and the SDK elf files. It may be used for a quick check on the system. All you need is the hardware and a PC running a UART terminal, ADI DAC software and the programmer (IMPACT). The notes below refer to ML605, but the procedure is same for all the boards.
Required Hardware
- ML605/KC705/VC707 board
- AD9739A-EBZ board & Power supply
- DAC FMC interposer board
- Signal/Clock generator (2.5GHz)
- Spectrum Analyzer
Required Software
- Xilinx ISE 13.2 (Programmer (IMPACT) is sufficient for the demo and is available on Webpack).
- A UART terminal (Tera Term/Hyperterminal), Baud rate 57600.
- ADI DPG DAC Software Suite available here.
Bit file
- Download the gzip file and extract the sw/cf_ad9739a_ebz
.bit file.
Running Demo (SDK) Program
To begin make the following connections (see image below):
- Connect the AD9739A-EBZ board to the FMC Interposer board.
- Connect the interposer board to the FMC-LPC connector of ML605 board.
- Connect power to ML605 and the AD9739A-EBZ boards.
- Connect two USB cables from the PC to the JTAG and UART USB connectors on ML605.
- Connect a USB cable to the AD9739A-EBZ board.
- Connect an external clock source to AD9739A-EBZ board's J3 SMA connector.
- Connect a spectrum analyzer to AD9739A-EBZ board's J1 SMA connector.
Setup the clock source to be 2.5GHz. If you wish to run the device at a different clock rate, please change the SDK c program accordingly. After the hardware setup, turn the power on to the ML605 and the AD9739A-EBZ boards.
Start ADI- AD9739A SPI program (see screenshot below)-
- (1) click on “Run Continously” button.
- (2) click on “MU_ENA” button.
- (3) make sure that “MU_LCK” has turned green.
Start IMPACT, and initialze the JTAG chain. The program should recognize the Virtex 6 device (see screenshot below). Start a UART terminal (set to 57600 baud rate) and then program the device.
If programming was successful, you should be seeing messages appear on the terminal as shown in figure below.
Now enable the receivers via the ADI- AD9739A SPI program (see screenshot above)-
- (4) click on “RCV_ENA” button.
- (5) click on “RCV_LOOP” button.
- (6) make sure that “RCV_LCK” and “RCV_TRACK” has turned green.
After DDS is enabled, you should see the spectrum analyzer displaying the 300MHz tone.
Using the reference design
Functional description
The reference design consists of a DDS module and a lvds interface.
The DDS module consists of a Xilinx DDS core and DDR based DDS. Internally the DDS runs at fDAC/3 clock. The output samples are interleaved and driven by the lvds interface.
Registers
Refer to the regmap.txt file inside the pcore.
Downloads
FPGA Referece Designs:
Only Xilinx coregen xco files are provided with the reference design. You must regenerate the IP core files using this file. See generating Xilinx netlist/verilog files from xco files for details.
- Questions? Ask Help & Support.
Tar file contents
The tar file contains, in most cases, the following files and/or directories. To rebuild the reference design simply double click the XMP file and run the tool. To build SDK, select a workspace and use the C file to build the elf file. Please refer to Xilinx EDK documentation for details.
license.txt | ADI license & copyright information. |
system.mhs | MHS file. |
system.xmp | XMP file (use this file to build the reference design). |
data/ | UCF file and/or DDR MIG project files. |
docs/ | Documentation files (Please note that this wiki page is the documentation for the reference design). |
sw/ | Software (Xilinx SDK) & bit file(s). |
cf_lib/edk/pcores | The pcores directory. |
More information
- FMC插入器&Xilinx KC705參考設計
- AD7450A FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- AD7656-1 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- AD7658-1 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- ADC-FMC插入器&Xilinx ZC706參考設計
- AD9833 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- AD9789評估板、DAC-FMC轉接器和Xilinx ML605參考設計
- AD9129評估板、DAC-FMC插入器和Xilinx ML-605參考設計
- AD9671評估板、ADC-FMC轉接器和Xilinx KC705參考設計
- AD5780 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- AD5449 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- CN0204 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- AD7980 FMC-SDP轉接器和評估板/Xilinx KC705參考設計
- AD9467評估板、ADC-FMC插入器和Xilinx參考設計
- AD9122評估板、DAC-FMC插入器和Xilinx ML-605參考設計
- 【GD32F470紫藤派開發板使用手冊】第四講 FMC-片內Flash擦寫讀實驗 903次閱讀
- 淺析功分器的插入損耗和輸出駐波 1953次閱讀
- 系統演示平臺簡化了從評估到原型設計的過渡 646次閱讀
- 如何對PMDU和PMDE的發熱和效率進行比較評估 2470次閱讀
- 2.5GSPS高性能RF DAC AD9737A/AD9739A的主要特性及應用 5240次閱讀
- 了解光纖通信的插入損耗和回?fù)軗p耗 1.2w次閱讀
- Xilinx FPGA的FMC介紹 5643次閱讀
- 米爾科技 Beetle IoT 評估板概述 1189次閱讀
- digilent FMC Pcam適配器介紹 2731次閱讀
- digilent FMC-HDMI:雙HDMI輸入擴展子板介紹 4286次閱讀
- 2.5 GSPS高性能數模轉換器——AD9739A DAC 4675次閱讀
- 關于FPGA的FMC接口的詳細介紹 1.1w次閱讀
- 詳解Xilinx公司Zynq? UltraScale+?MPSoC產品 3184次閱讀
- 德州儀器LaunchPad系列 ADS1118評估板評測 4092次閱讀
- Maxim為三款Xilinx FPGA參考設計提供電源管理方案 1163次閱讀
下載排行
本周
- 1電子電路原理第七版PDF電子教材免費下載
- 0.00 MB | 1491次下載 | 免費
- 2單片機典型實例介紹
- 18.19 MB | 95次下載 | 1 積分
- 3S7-200PLC編程實例詳細資料
- 1.17 MB | 27次下載 | 1 積分
- 4筆記本電腦主板的元件識別和講解說明
- 4.28 MB | 18次下載 | 4 積分
- 5開關電源原理及各功能電路詳解
- 0.38 MB | 11次下載 | 免費
- 6100W短波放大電路圖
- 0.05 MB | 4次下載 | 3 積分
- 7基于單片機和 SG3525的程控開關電源設計
- 0.23 MB | 4次下載 | 免費
- 8基于AT89C2051/4051單片機編程器的實驗
- 0.11 MB | 4次下載 | 免費
本月
- 1OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 2PADS 9.0 2009最新版 -下載
- 0.00 MB | 66304次下載 | 免費
- 3protel99下載protel99軟件下載(中文版)
- 0.00 MB | 51209次下載 | 免費
- 4LabView 8.0 專業版下載 (3CD完整版)
- 0.00 MB | 51043次下載 | 免費
- 5555集成電路應用800例(新編版)
- 0.00 MB | 33562次下載 | 免費
- 6接口電路圖大全
- 未知 | 30320次下載 | 免費
- 7Multisim 10下載Multisim 10 中文版
- 0.00 MB | 28588次下載 | 免費
- 8開關電源設計實例指南
- 未知 | 21539次下載 | 免費
總榜
- 1matlab軟件下載入口
- 未知 | 935053次下載 | 免費
- 2protel99se軟件下載(可英文版轉中文版)
- 78.1 MB | 537793次下載 | 免費
- 3MATLAB 7.1 下載 (含軟件介紹)
- 未知 | 420026次下載 | 免費
- 4OrCAD10.5下載OrCAD10.5中文版軟件
- 0.00 MB | 234313次下載 | 免費
- 5Altium DXP2002下載入口
- 未知 | 233046次下載 | 免費
- 6電路仿真軟件multisim 10.0免費下載
- 340992 | 191183次下載 | 免費
- 7十天學會AVR單片機與C語言視頻教程 下載
- 158M | 183277次下載 | 免費
- 8proe5.0野火版下載(中文版免費下載)
- 未知 | 138039次下載 | 免費
評論
查看更多