智能手機與星火一號開發板之間的WIFI通訊設計實現

簡介

本項目的主要功能是通過定義星火1號開發板上相應IO的電平狀態，調試智能手機與星火一號開發板之間的WIFI通訊，從而通過手機輸入相關的命令，實現對麥克納姆輪四驅小車的移動控制（如下圖所示）

硬件介紹

開發板

使用 RT-Thread 星火 1 號 開發板開發本項目，各模塊在開發板中位置如圖所示

RSAPBEERY CONN

如上圖所示，開發板RSAPBEERY CONN中各引腳與對應L298N中輸入輸出口的對應關系

RW007 WIFI

供電方案

八節5號電池串聯提供12V電壓（兩個L298N，兩個電池盒共計16個電池）：優點是供電較為穩定其，缺點是其重量過大，可能導致小車速度下降。

充電寶3.6V+升壓模塊升至12V：利用可調輸出電壓的升壓模塊可以輸出12V電壓供L298N使用。但是因?yàn)槌潆妼?、升壓模塊不穩定，其無法穩定輸出12V電壓，故而舍棄此方案。

接線

接線如上圖所示，各個端口所對應具體情況如下：

電源線：+12V接升壓模塊OUT+
GND接升壓模塊OUT-
GND接開發板GND
+5V接開發板+5V

邏輯控制

對于Motor_A（小車前輪的兩個電機）和Motor_B（小車前輪的兩個電機）的控制邏輯如下，其中本項目使用的是PIN，因此無需考慮PWM

杜邦線

紅色：通常用于連接電源正極或高電平信號。

黑色：通常用于連接電源負極或地線。

藍色、綠色、黃色等其他顏色：通常用于連接數據線或其他信號線，具體用途取決于具體的電路設計。

小車裝配

第一層：電池盒及電池
第二層：星火1號開發板
第三層：L298N電機驅動模塊、輪子、電機

軟件介紹

WIFI 完成初始化

static int i = 0;
int result = RT_EOK;
struct rt_wlan_info info;
rt_thread_mdelay(500);
熱點掃描
/* 執行掃描 */
rt_sem_init(&scan_done,"scan_done",0,RT_IPC_FLAG_FIFO);
rt_wlan_register_event_handler(RT_WLAN_EVT_SCAN_REPORT, wlan_scan_report_hander,&i);
rt_wlan_register_event_handler(RT_WLAN_EVT_SCAN_DONE, wlan_scan_done_hander,RT_NULL);
if(rt_wlan_scan() == RT_EOK)
{
LOG_D("the scan is started... ");
}else
{
LOG_E("scan failed");
}
/*等待掃描完畢 /
rt_sem_take(&scan_done,RT_WAITING_FOREVER);
Join 網絡
/ 熱點連接 /
LOG_D("start to connect ap ...");
rt_sem_init(&net_ready, "net_ready", 0, RT_IPC_FLAG_FIFO);
/ 注冊 wlan ready 回調函數 /
rt_wlan_register_event_handler(RT_WLAN_EVT_READY, wlan_ready_handler, RT_NULL);
/ 注冊 wlan 斷開回調函數 /
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_DISCONNECTED, wlan_station_disconnect_handler, RT_NULL);
/ 同步連接熱點 /
result = rt_wlan_connect(WLAN_SSID, WLAN_PASSWORD);
if (result == RT_EOK)
{
rt_memset(&info, 0, sizeof(struct rt_wlan_info));
/ 獲取當前連接熱點信息 /
rt_wlan_get_info(&info);
LOG_D("station information:");
print_wlan_information(&info,0);
/ 等待成功獲取 IP /
result = rt_sem_take(&net_ready, NET_READY_TIME_OUT);
if (result == RT_EOK)
{
LOG_D("networking ready!");
msh_exec("ifconfig", rt_strlen("ifconfig"));
}
else
{
LOG_D("wait ip got timeout!");
}
/ 回收資源 */
rt_wlan_unregister_event_handler(RT_WLAN_EVT_READY);
rt_sem_detach(&net_ready);
}
else
{
LOG_E("The AP(%s) is connect failed!", WLAN_SSID);
}
rt_thread_mdelay(5000);
LOG_D("ready to disconect from ap ...");
rt_wlan_disconnect();
自動連接
LOG_D("start to autoconnect ...");
wifi_autoconnect();

串口連接模塊

使用sscom5發送數據，rt-studio平臺接收數據，數據作為參數傳入到電機控制模塊

static const char send_data[] = "This is TCP Client from RT-Thread."; /* 發送用到的數據 */
char recv_data;
#define THREAD_PRIORITY 25
#define THREAD_STACK_SIZE 512
#define THREAD_TIMESLICE 5
static rt_thread_t tid1 = RT_NULL;
static rt_thread_t tid2 = RT_NULL;
/ 線程2的入口函數 */
static void thread2_entry(void *parameter)
{
int ret;
struct hostent *host;
int sock, bytes_received;
struct sockaddr_in server_addr;
const char url;
int port;
url = "192.168.43.96";
port = 8800;
/ 通過函數入口參數url獲得host地址（如果是域名，會做域名解析） /
host = gethostbyname(url);
/ 分配用于存放接收數據的緩沖 /
recv_data = rt_malloc(BUFSZ);
if (recv_data == RT_NULL)
{
rt_kprintf("No memoryn");
return;
}
/ 創建一個socket，類型是SOCKET_STREAM，TCP類型 /
if ((sock = socket(AF_INET, SOCK_STREAM, 0)) == -1)
{
/ 創建socket失敗 /
rt_kprintf("Socket errorn");
/ 釋放接收緩沖 /
rt_free(recv_data);
return;
}
/ 初始化預連接的服務端地址 */
server_addr.sin_family = AF_INET;
server_addr.sin_port = htons(port);
server_addr.sin_addr = *((struct in_addr )host->h_addr);
rt_memset(&(server_addr.sin_zero), 0, sizeof(server_addr.sin_zero));
/ 連接到服務端 */
if (connect(sock, (struct sockaddr )&server_addr, sizeof(struct sockaddr)) == -1)
{
/ 連接失敗 /
rt_kprintf("Connect fail!n");
closesocket(sock);
/ 釋放接收緩沖 /
rt_free(recv_data);
return;
}
while (1)
{
/ 從sock連接中接收最大BUFSZ - 1字節數據 /
bytes_received = recv(sock, recv_data, BUFSZ - 1, 0);
if (bytes_received < 0)
{
/ 接收失敗，關閉這個連接 /
closesocket(sock);
rt_kprintf("nreceived error,close the socket.rn");
/ 釋放接收緩沖 /
rt_free(recv_data);
break;
}
else if (bytes_received == 0)
{
/ 默認 recv 為阻塞模式，此時收到0認為連接出錯，關閉這個連接 /
closesocket(sock);
rt_kprintf("nreceived error,close the socket.rn");
/ 釋放接收緩沖 /
rt_free(recv_data);
break;
}
/ 有接收到數據，把末端清零 /
recv_data[bytes_received] = '?';
if (strncmp(recv_data, "q", 1) == 0 || strncmp(recv_data, "Q", 1) == 0)
{
/ 如果是首字母是q或Q，關閉這個連接 /
closesocket(sock);
rt_kprintf("n got a 'q' or 'Q',close the socket.rn");
/ 釋放接收緩沖 /
rt_free(recv_data);
break;
}
else
{
/ 在控制終端顯示收到的數據 /
rt_kprintf("nReceived data = %s ", recv_data);
}
/ 發送數據到sock連接 /
ret = send(sock, send_data, strlen(send_data), 0);
if (ret < 0)
{
/ 接收失敗，關閉這個連接 /
closesocket(sock);
rt_kprintf("nsend error,close the socket.rn");
rt_free(recv_data);
break;
}
else if (ret == 0)
{
/ 打印send函數返回值為0的警告信息 /
rt_kprintf("n Send warning,send function return 0.rn");
}
}
return;
rt_thread_mdelay(500);
}
/ 線程2 /
int thread2_sample(void)
{
/ 創建線程2，名稱是thread2，入口是thread2_entry /
tid2 = rt_thread_create("thread2",
thread2_entry, RT_NULL,
2048,
THREAD_PRIORITY, THREAD_TIMESLICE);
/ 如果獲得線程控制塊，啟動這個線程 /
if (tid2 != RT_NULL)
rt_thread_startup(tid2);
return 0;
}
MSH_CMD_EXPORT(thread2_sample, thread sample);
開發板IO引腳定義
/ 配置 控制電機引腳(L2980N1) /
#define PIN_Motor_PA0 GET_PIN(A, 0) // PA0 : define --> Motor1
#define PIN_Motor_PA8 GET_PIN(A, 8) // PA8 : define --> Motor1
#define PIN_Motor_PB15 GET_PIN(B, 15) // PB15: define --> Motor2
#define PIN_Motor_PB14 GET_PIN(B, 14) // PB14: define --> Motor2
/ 配置 控制電機引腳(L2980N2) /
#define PIN_Motor_PB2 GET_PIN(B, 2) // PB2 : define --> Motor3
#define PIN_Motor_PG6 GET_PIN(G, 6) // PG6 : define --> Motor3
#define PIN_Motor_PG7 GET_PIN(G, 7) // PG7 : define --> Motor4
#define PIN_Motor_PD7 GET_PIN(D, 7) // PD7 : define --> Motor4
/ 定義電機引腳宏 */
#define PIN_Motor1_A PIN_Motor_PA0
#define PIN_Motor1_B PIN_Motor_PA8
#define PIN_Motor2_A PIN_Motor_PB15
#define PIN_Motor2_B PIN_Motor_PB14
#define PIN_Motor3_A PIN_Motor_PB2
#define PIN_Motor3_B PIN_Motor_PG6
#define PIN_Motor4_A PIN_Motor_PG7
#define PIN_Motor4_B PIN_Motor_PD7

小車行駛控制

通過設置對應IO引腳的高低電平，可以控制電機的轉動和停止，從而控制小車的前進，后退，左移和右移

/* 控制小車前進 /
void motor_forward(void) {
// 向前加速1s
rt_pin_write(PIN_Motor1_A, PIN_HIGH);
rt_pin_write(PIN_Motor1_B, PIN_LOW);
rt_pin_write(PIN_Motor2_A, PIN_HIGH);
rt_pin_write(PIN_Motor2_B, PIN_LOW);
rt_pin_write(PIN_Motor3_A, PIN_HIGH);
rt_pin_write(PIN_Motor3_B, PIN_LOW);
rt_pin_write(PIN_Motor4_A, PIN_HIGH);
rt_pin_write(PIN_Motor4_B, PIN_LOW);
rt_thread_mdelay(1000);
//停下
rt_pin_write(PIN_Motor1_A, PIN_LOW);
rt_pin_write(PIN_Motor1_B, PIN_LOW);
rt_pin_write(PIN_Motor2_A, PIN_LOW);
rt_pin_write(PIN_Motor2_B, PIN_LOW);
rt_pin_write(PIN_Motor3_A, PIN_LOW);
rt_pin_write(PIN_Motor3_B, PIN_LOW);
rt_pin_write(PIN_Motor4_A, PIN_LOW);
rt_pin_write(PIN_Motor4_B, PIN_LOW);
}
/ 控制小車后退 /
void motor_backward(void) {
// 向后加速1s
rt_pin_write(PIN_Motor1_A, PIN_LOW);
rt_pin_write(PIN_Motor1_B, PIN_HIGH);
rt_pin_write(PIN_Motor2_A, PIN_LOW);
rt_pin_write(PIN_Motor2_B, PIN_HIGH);
rt_pin_write(PIN_Motor3_A, PIN_LOW);
rt_pin_write(PIN_Motor3_B, PIN_HIGH);
rt_pin_write(PIN_Motor4_A, PIN_LOW);
rt_pin_write(PIN_Motor4_B, PIN_HIGH);
rt_thread_mdelay(1000);
//停下
rt_pin_write(PIN_Motor1_A, PIN_LOW);
rt_pin_write(PIN_Motor1_B, PIN_LOW);
rt_pin_write(PIN_Motor2_A, PIN_LOW);
rt_pin_write(PIN_Motor2_B, PIN_LOW);
rt_pin_write(PIN_Motor3_A, PIN_LOW);
rt_pin_write(PIN_Motor3_B, PIN_LOW);
rt_pin_write(PIN_Motor4_A, PIN_LOW);
rt_pin_write(PIN_Motor4_B, PIN_LOW);
}
/ 控制小車左走*/
void motor_left(void) {
// 向左加速0.5s
rt_pin_write(PIN_Motor1_A, PIN_LOW);
rt_pin_write(PIN_Motor1_B, PIN_HIGH);
rt_pin_write(PIN_Motor2_A, PIN_HIGH);
rt_pin_write(PIN_Motor2_B, PIN_LOW);
rt_pin_write(PIN_Motor3_A, PIN_HIGH);
rt_pin_write(PIN_Motor3_B, PIN_LOW);
rt_pin_write(PIN_Motor4_A, PIN_LOW);
rt_pin_write(PIN_Motor4_B, PIN_HIGH);
rt_thread_mdelay(1000);
//停下
rt_pin_write(PIN_Motor1_A, PIN_LOW);
rt_pin_write(PIN_Motor1_B, PIN_LOW);
rt_pin_write(PIN_Motor2_A, PIN_LOW);
rt_pin_write(PIN_Motor2_B, PIN_LOW);
rt_pin_write(PIN_Motor3_A, PIN_LOW);
rt_pin_write(PIN_Motor3_B, PIN_LOW);
rt_pin_write(PIN_Motor4_A, PIN_LOW);
rt_pin_write(PIN_Motor4_B, PIN_LOW);
}
/* 控制小車右走 /
void motor_right(void) {
// 向右加速0.5s
rt_pin_write(PIN_Motor1_A, PIN_HIGH);
rt_pin_write(PIN_Motor1_B, PIN_LOW);
rt_pin_write(PIN_Motor2_A, PIN_LOW);
rt_pin_write(PIN_Motor2_B, PIN_HIGH);
rt_pin_write(PIN_Motor3_A, PIN_LOW);
rt_pin_write(PIN_Motor3_B, PIN_HIGH);
rt_pin_write(PIN_Motor4_A, PIN_HIGH);
rt_pin_write(PIN_Motor4_B, PIN_LOW);
rt_thread_mdelay(1000);
//停下
rt_pin_write(PIN_Motor1_A, PIN_LOW);
rt_pin_write(PIN_Motor1_B, PIN_LOW);
rt_pin_write(PIN_Motor2_A, PIN_LOW);
rt_pin_write(PIN_Motor2_B, PIN_LOW);
rt_pin_write(PIN_Motor3_A, PIN_LOW);
rt_pin_write(PIN_Motor3_B, PIN_LOW);
rt_pin_write(PIN_Motor4_A, PIN_LOW);
rt_pin_write(PIN_Motor4_B, PIN_LOW);
}
/ 線程1的入口函數 /
static void thread1_entry(void parameter)
{
rt_pin_mode(PIN_Motor_PA0, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PA8, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PB15, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PB14, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PB2, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PG6, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PG7, PIN_MODE_OUTPUT);
rt_pin_mode(PIN_Motor_PD7, PIN_MODE_OUTPUT);
while (1)
{
/ 線程1采用低優先級運行，一直打印計數值 /
if (strcmp(recv_data, "a") == 0) {
motor_forward();
// rt_kprintf(" data:%s rn",recv_data);
rt_memset(recv_data, 0, strlen(recv_data));
}
else if (strcmp(recv_data, "b") == 0) {
motor_backward();
rt_memset(recv_data, 0, strlen(recv_data));
}
else if (strcmp(recv_data, "c") == 0) {
motor_left();
rt_memset(recv_data, 0, strlen(recv_data));
}
else if (strcmp(recv_data, "d") == 0) {
motor_right();
rt_memset(recv_data, 0, strlen(recv_data));
}
rt_thread_mdelay(500);
}
}
/ 線程1 /
int thread1_sample(void)
{
/ 創建線程1，名稱是thread1，入口是thread1_entry /
tid1 = rt_thread_create("thread1",
thread1_entry, RT_NULL,
THREAD_STACK_SIZE,
THREAD_PRIORITY, THREAD_TIMESLICE);
/* 如果獲得線程控制塊，啟動這個線程 /
if (tid1 != RT_NULL)
rt_thread_startup(tid1);
return 0;
}
/ 導出到 msh 命令列表中 */
MSH_CMD_EXPORT(thread1_sample, thread sample);

運行結果

最后，在完成上面步驟后，我們通過命令行執行一下代碼（如下圖）即可完成小車與控制設備的WIFI連接（下面代碼以小車與智能手機的WIFI連接為例）