DS2148/DS21348 Hardware Mode

Abstract: Application Note 407 provides a focused view of the functionality of the Dallas Semiconductor/Maxim DS2148/DS21348 selectable E1 or T1 line interface unit (LIU) in hardware mode along with references to software mode features to aid designers creating applications using hardware mode only.

Introduction

There are two major modes of operation for the DS2148/DS21348: software and hardware mode. The "mode" refers to the method used to control the functionality of the device. Applications implementing software mode use a microcontroller's serial or parallel bus to communicate to the control registers contained in the DS2148/DS21348. In hardware mode, the functions of the serial/parallel communication bus pins are reassigned such that the pins' logic state provide direct control of the internal functionality of the DS2148/DS21348.

The DS2148 and DS21348 data sheets contain all the information required to implement the DS2148/DS21348 in designs using a T1 or E1 interface. The data sheets were written with the software mode user in mind and therefore contain information required to set up the DS2148/DS21348 using the control registers and the additional functionality available in software mode that is not available when using hardware mode.

This application note provides a focused view of the functionality of the DS2148/DS21348 in hardware mode along with references to software mode features to aid designers creating applications using hardware mode only.

Should Hardware Mode Be Used?

The advantage of using the DS2148/DS21348 in hardware mode is that no microcontroller is required to control the functionality. Each application has specific requirements that determine whether or not hardware mode can be used. The primary consideration is whether or not any of the features available only in software mode are required in the application. Table 1 provides a list of all the software mode features that are totally eliminated in hardware mode. The register bit position and name is provided to allow ease in referencing the complete description of the functionality contained in the DS2148 and DS21348 data sheets.

Hardware Mode Implementation

All the primary functions that require the ability to change are controlled by external pins in hardware mode. Table 2 provides a reference for the functionality of the software mode bit positions and the corresponding pin that is used in hardware mode to control the DS2148/348.

While some software controllable features are unavailable in hardware mode, the DS2148/DS21348 default functionality was carefully chosen to perform as expected in normal applications. Table 3 lists the features and their default operation in hardware mode. A complete description of the hardware mode functionality of each of the pins is provided in Table 4.

Figures 1, 2, and 3 provide block diagrams representative of the functionality of the DS2148/DS21348 in hardware mode and are similar to their software mode counterparts in the data sheets. In contrast to the block diagrams provided in the data sheets, the external pins of the DS2148/DS21348 replace references to the control registers. Software-mode-only functions have also been removed.

Although most DS2148/DS21348 applications implement software mode, hardware mode remains a viable option for many customers. Using this document along with the DS2148 and DS21348 data sheets provides the information required to get a hardware mode application up and running with minimal time and effort.

Table 1. Software mode features eliminated in hardware mode

Position	Function
CCR1.4	Error Counter Update Enable
CCR1.2	TCLK to JACLK
CCR1.1	TCLK to RCLK
CCR1.0	Loss-of-Transmit Clock Mux Control
CCR2.4	Custom Line Driver Select
CCR3.6	Automatic Transmit Unframed All Ones
CCR3.3	Transmit Loop Code Enable
CCR3.2	Line Interface Reset
CCR3.1	Insert BPV
CCR3.0	Insert Bit Error
CCR5.7	Backplane Clock Select 1
CCR5.6	Backplane Clock Select 0
CCR6.5	Automatic Remote Loopback Enable and Reset
CCR6.3	RCLK Jitter Attenuator Bypass
CCR6.2	Error Count Register Select 2
CCR6.1	Error Count Register Select 1
CCR6.0	Error Count Register Select 0

Table 2. Hardware mode pin control/register reference

Position	Pin	Function
CCR1.7	ETS	E1/T1 Select
CCR1.6	NRZE	NRZ Enable
CCR1.3	JAMUX	Jitter Attenuator Mux
CCR2.3	HBE	Receive HDB3/B8ZS Enable
CCR2.2	HBE	Transmit HDB3.B8ZS Enable
CCR2.1	CES	Transmit Clock Edge Select
CCR2.0	CES	Receive Clock Edge Select
CCR3.7	TX0, TX1	Transmit Unframed All Ones
CCR3.5	TX0, TX1	Transmit Alternate Ones and Zeros
CCR3.4	TX0, TX1	Transmit Alternates Ones and Zeros
CCR4.7	L2	Line Build-Out Select Pin 2
CCR4.6	L1	Line Build-Out Select Pin 1
CCR4.5	L0	Line build-Out Select Pin 0
CCR4.4	EGL	Receive Equalizer Gain Limit
CCR4.3	JAS	Jitter Attenuator Select
CCR4.1	DJA	Disable Jitter Attenuator
CCR4.0	TPD	Transmit Power-Down
CCR5.5	MM1	Monitor Mode 1
CCR5.4	MM0	Monitor Mode 0
CCR5.3	SCLKE	Receive Synchronization Clock Enable
CCR5.2	SCLKE	Transmit Synchronization Clock Enable
CCR5.1	RT1	Receive Termination 1
CCR5.0	RT0	Receive Termination 0
CCR6.7	LOOP0, LOOP1	Local Loopback
CCR6.6	LOOP0, LOOP1	Remote Loopback
CCR6.4	LOOP0, LOOP1	Analog Loopback

Table 3. Hardware mode default functionality

Position	Function	Hardware Mode Function
CCR1.5	Receive Carrier Loss Alternate Criteria	RCL declared upon 255 (E1) or 192 (T1) consecutive zeros
CCR2.7	Pin 25 Select	Toggles high during a receive carrier loss condition
CCR2.5	Short Circuit Limit Disable	50mA current-limiter enabled
CCR4.2	Jitter Attenuator Buffer Depth Select	128 bits

Table 4. Pin descriptions in hardware mode (sorted by pin name, DS2148/348T pin numbering)

Name

Type

Function

BIS0

Bus Interface Select Pins 0 and 1. These pins are used to select the bus interface option. BISO = 1 and BIS1 = 1 selects the hardware mode.

BIS1

BPCLK

Backplane Clock. 16.384Mhz output

CES

Receive & Transmit Clock Edge Select. Selects which RCLK edge to update RPOS and RNEG and which TCLK edge to sample TPOS and TNEG.
0 = update RNEG/RPOS on rising edge of RCLK; sample TPOS/TNEG on falling edge of TCLK
1 = update RNEG/RPOS on falling edge of RCLK; sample TPOS/TNEG on rising edge of TCLK

DJA

Disable Jitter Attenuator
0 = jitter attenuator enabled 1 = jitter attenuator disabled

EGL

Receiver Equalizer Gain Limit. This bit controls the sensitivity of the receiver equalizer.
EGL E1 (ETS = 0)
0 = -12 dB (short haul)
1 = -43 dB (long haul)
EGL T1 (ETS = 1)
0 = -36 dB (long haul)
1 = -30 dB (limited long haul)

ETS

E1/T1 Select
0 = E1
1 = T1

HBE

Receive & Transmit HDB3/B8ZS Enable.
0 = enable HDB3 (E1) / B8ZS (T1)
1 = disable HDB3 (E1) / B8ZS (T1)

HRST

Hardware Reset. Bringing HRST low resets the DS21348

JAMUX

Jitter Attenuator MUX. Controls the source for JACLK.

E1 (ETS = 0)	JAMUX
MCLK = 2.048 MHz	0
T1 (ETS = 1)
MCLK = 2.048 MHz	1
MCLK = 1.544 MHz	0

JAS

Jitter Attenuator Selector.
0 = place the jitter attenuator on the receive side
1 = place the jitter attenuator on the transmit side

Transmit LIU Waveshape Select Pins 0, 1, & 2. These inputs determine the waveshape of the transmitter

L2	L1	L0	E1 (ETS = 0) APPLICATION
0	0	0	75Ω normal
0	0	1	120Ω normal
1	0	0	75Ω w/ high return loss
1	0	1	120Ω w/ high return loss
			T1 (ETS = 1) APPLICATION
0	0	0	DSX-1 (o to 133 feet) / 0dB CSU
0	0	1	DSX-1 (133 to 266 feet)
0	1	0	DSX-1 (266 to 399 feet)
0	1	1	DSX-1 (399 to 533 feet)
1	0	0	DSX-1 (533 to 655 feet)
1	0	1	-7.5 dB CSU
1	1	0	-15 dB CSU
1	1	1	-22.5 dB CSU

LOOP0

Loopback Select Bits 0 & 1. These inputs determine the active loopback mode (if any).

LOOP1	LOOP0	SYMBOL	LOOPBACK
0	0	---	No Loopback
0	1	ALB	Analog Loopback
1	0	LLB	Local Loopback
1	1	RLB	Remote Loopback

LOOP1

MCLK

Master Clock. A 2.048MHz (±50ppm) clock source with TTL levels is applied at this pin. This clock is used internally for both clock/data recovery and for jitter attenuation. Use of a T1 1.544 MHz clock source is optional. G.703 requires an accuracy of ±50ppm for both T1 and E1. TR62411 and ANSI specs require an accuracy of ±32ppm for T1 interfaces.

MM0

Monitor Mode Select Pins 0 & 1. These inputs determine if the receive equalizer is in a monitor mode.

MM1	MM0	INTERNAL GAIN BOOST
0	0	Normal operation (no boost)
0	1	20dB
1	0	26dB
1	1	32dB

MM1

NRZE

NRZ Enable
0 = Bipolar data at RPOS/RNEG and TPOS/TNEG
1 = NRZ data at RPOS and TPOS or TNEG; RNEG outputs a positive outgoing pulse when device receives a BPV, CV, or EXZ.

PBEO

PRBS Pin Error Output. The receiver will constantly search for a QRSS (T1) or a 215 - 1 (E1) PRBS depending on whether T1 or E1 mode is selected. Remains high if out of synchronization with the PRBS pattern. Goes low when synchronized to the PRBS pattern. Any errors in the received pattern after synchronization will cause a positive-going pulse (with same period as E1 or T1 clock) synchronous with RCLK.

RCLK

Receive Clock. Buffered recovered clock from the line. Synchronous to MCLK in absence of signal at RTIP and RRING.

RCL

Receive Carrier Loss. An output which will toggle high during a receive carrier loss.

RNEG

Receive Negative Data. Updated on the rising edge (CES = 0) or the falling edge (CES = 1) of RCLK with the bipolar data out of the line interface. Set NRZE to a one for NRZ applications. In NRZ mode, data will be output on RPOS while a received error will cause a positive-going pulse synchronous with RCLK at RNEG.

RPOS

Receive Positive Data. Updated on the rising edge (CES = 0) or the falling edge (CES = 1) of RCLK with bipolar data out of the line interface. Set NRZE to a one for NRZ applications. In NRZ mode, data will be output on RPOS while a received error will cause a positive-going pulse synchronous with RCLK at RNEG.

RT0

Receive LIU Termination Select Pins 0 & 1. These inputs determine the receive termination.

	INTERNAL RECEIVE
RT1	RT0	TERMINATION CONFIGURATION
0	0	Internal receive-side termination disabled
0	1	Internal receive-side 120Ω enabled
1	0	Internal receive-side 100Ω enabled
1	1	Internal receive-side 75Ω enabled

RT1

RTIP

Receive Tip and Ring. Analog inputs for clock recovery circuitry. These pins connect via a 1:1 transformer to the line.

RRING

SCLKE

Receive and Transmit Synchronization Clock Enable.
0 = disable 2.048MHz synchronization transmit and receive mode
1 = enable 2.048MHz synchronization transmit and receive mode

TCLK

Transmit Clock. A 2.048MHz or 1.544MHz primary clock. Used to clock data through the transmit side formatter.

TEST

Tri-State Control. Set high to tri-state all outputs and I/O pins. Set low for normal operation. Useful in board level testing.

TNEG

Transmit Negative Data. Sampled on the falling edge (CES = 0) or the rising edge (CES = 1) of TCLK for data to be transmitted out onto the line.

TPD

Transmit Power-Down
0 = normal transmitter operation
1 = powers down the transmitter and tri-states the TTIP and TRING pins

TPOS

Transmit Positive Data. Sampled on the falling edge (CES = 0) or the rising edge (CES = 1) of TCLK for data to be transmitted out onto the line.

TTIP

Transmit Tip and Ring [TTIP and TRING]. Analog line-driver outputs. These pins connect via a step-up transformer to the line.

TRING

TX0

Transmit Data Source Select Pins 0 & 1. These inputs determine the source of the transmit data.

TX1	TX0	SYMBOL	TRANSMIT DATA
0	0	---	TPOS & TNEG
0	1	TPRBSE	Transmit PRBS
1	0	TAOZ	Transmit Alternating Ones and Zeros
1	1	TUA1	Transmit Unframed All Ones

TX1

VDD

21, 36

---

Positive Supply. DS2148 = 5.0V ±5%; DS21348 = 3.3V ±5%

VSM

Voltage Supply Mode. DS2148 = connect to VDD. DS21348 = connect to VSS.

VSS

22, 35

---

Signal Ground

Figure 1. DS2148/DS21348 hardware mode block diagram.

Figure 2. DS2148/DS21348 hardware mode receive logic.

Figure 3. DS2148/DS21348 hardware mode transmit logic.

閱讀全文

DS2(42921) DS2(42921)
DS2148(5650) DS2148(5650)

DS21348DK

KIT EVALUATION FOR DS21348

2023-03-30 11:45:57

DS2148DK

DS2148 - Telecom, Line Interface Units (LIUs) Evaluation Board

2023-03-30 11:44:05

DS-5教程-ARM DS-5 添加新芯片至DS-5調試設備列表

utility（/home/userx/DS-5/bin/cdbimporter）Hardware Configuration utility（/home/userx/DS-5/bin/dbghwconfig

2014-10-13 18:17:15

DS1702K

DS75, DS1621, DS1624, DS1629, DS1721, DS1775 - Temperature Sensor Evaluation Board

2023-03-30 11:59:31

DS2431

********************************************************//******************************************函數名稱：GPIO_DS2431_Out_Mode功能：設置DS2431引腳為開漏輸出

2014-03-12 11:04:08

DS32W

2023-03-29 21:39:21

A02DS02DS28W152B

JUMPER02DS-8E-02DS-8E6"

2023-03-22 22:25:42

A02DS02DS28W305B

JUMPER02DS-8E-02DS-8E12"

2023-03-22 22:25:42

A02DS02DS28W51B

JUMPER02DS-8E-02DS-8E2"

2023-03-22 22:25:39

A03DS03DS28W152B

JUMPER03DS-8E-03DS-8E6"

2023-03-22 22:25:56

A03DS03DS28W305B

JUMPER03DS-8E-03DS-8E12"

2023-03-22 22:25:57

A03DS03DS28W51B

JUMPER03DS-8E-03DS-8E2"

2023-03-22 22:25:55

A04DS04DS28W152B

JUMPER04DS-8E-04DS-8E6"

2023-03-22 22:25:42

A04DS04DS28W305B

JUMPER04DS-8E-04DS-8E12"

2023-03-22 22:25:43

A04DS04DS28W51B

JUMPER04DS-8E-04DS-8E2"

2023-03-22 22:25:42

A05DS05DS28W152B

JUMPER05DS-8E-05DS-8E6"

2023-03-22 22:25:59

A05DS05DS28W305B

JUMPER05DS-8E-05DS-8E12"

2023-03-22 22:26:01

A05DS05DS28W51B

JUMPER05DS-8E-05DS-8E2"

2023-03-22 22:26:00

A06DS06DS28W152B

JUMPER06DS-8E-06DS-8E6"

2023-03-22 22:25:45

A06DS06DS28W305B

JUMPER06DS-8E-06DS-8E12"

2023-03-22 22:25:47

A06DS06DS28W51B

JUMPER06DS-8E-06DS-8E2"

2023-03-22 22:25:44

A07DS07DS28W152B

JUMPER07DS-8E-07DS-8E6"

2023-03-22 22:26:03

A07DS07DS28W305B

JUMPER07DS-8E-07DS-8E12"

2023-03-22 22:26:06

A07DS07DS28W51B

JUMPER07DS-8E-07DS-8E2"

2023-03-22 22:26:01

A08DS08DS28W152B

JUMPER08DS-8E-08DS-8E6"

2023-03-22 22:25:47

A08DS08DS28W305B

JUMPER08DS-8E-08DS-8E12"

2023-03-22 22:25:49

A08DS08DS28W51B

JUMPER08DS-8E-08DS-8E2"

2023-03-22 22:25:45

A09DS09DS28W152B

JUMPER09DS-8E-09DS-8E6"

2023-03-22 22:26:07

A09DS09DS28W305B

JUMPER09DS-8E-09DS-8E12"

2023-03-22 22:26:11

A09DS09DS28W51B

JUMPER09DS-8E-09DS-8E2"

2023-03-22 22:26:05

A10DS10DS28W152B

JUMPER10DS-8E-10DS-8E6"

2023-03-22 22:26:08

A10DS10DS28W305B

JUMPER10DS-8E-10DS-8E12"

2023-03-22 22:26:13

A10DS10DS28W51B

JUMPER10DS-8E-10DS-8E2"

2023-03-22 22:26:06

A11DS11DS28W152B

JUMPER11DS-8E-11DS-8E6"

2023-03-22 22:26:12

A11DS11DS28W305B

JUMPER11DS-8E-11DS-8E12"

2023-03-22 22:26:16

A11DS11DS28W51B

JUMPER11DS-8E-11DS-8E2"

2023-03-22 22:26:10

A12DS12DS28W152B

JUMPER12DS-8E-12DS-8E6"

2023-03-22 22:26:15

A12DS12DS28W305B

JUMPER12DS-8E-12DS-8E12"

2023-03-22 22:26:19

A12DS12DS28W51B

JUMPER12DS-8E-12DS-8E2"

2023-03-22 22:26:13

A13DS13DS28W152B

JUMPER13DS-8E-13DS-8E6"

2023-03-22 22:26:15

A13DS13DS28W305B

JUMPER13DS-8E-13DS-8E12"

2023-03-22 22:26:20

A13DS13DS28W51B

JUMPER13DS-8E-13DS-8E2"

2023-03-22 22:26:13

A14DS14DS28W152B

JUMPER14DS-8E-14DS-8E6"

2023-03-22 22:26:18

A14DS14DS28W305B

JUMPER14DS-8E-14DS-8E12"

2023-03-22 22:26:21

A14DS14DS28W51B

JUMPER14DS-8E-14DS-8E2"

2023-03-22 22:26:14

A15DS15DS28W152B

JUMPER15DS-8E-15DS-8E6"

2023-03-22 22:26:19

A15DS15DS28W305B

JUMPER15DS-8E-15DS-8E12"

2023-03-22 22:26:22

A15DS15DS28W51B

JUMPER15DS-8E-15DS-8E2"

2023-03-22 22:26:14

LSM9DS0和LSM9DS1之間的磁強計差異

我們正在將IMU從LSM9DS0升級到LSM9DS1。但是我們在LSM9DS1上遇到了磁力計的問題。即使在最小/最大校準之后，它似乎也沒有給出正確的航向。我們意識到方向已經改變并考慮到了這一點。當

2019-06-12 13:10:48

STM32與DS1302接口

作者在某STM32的應用中外接了一塊DS1302，借鑒原來寫過的PIC代碼，很快移植成功。在這里與大家分享一下。（1）硬件 CLK PA4DAT PA5 RST PA6（2）硬件初始化 CLK

2011-07-26 09:14:53

U-F-M5DS-Y-2

2023-03-29 17:44:28

U-F-M5DS-Y-5

2023-03-29 21:43:33

U-F-M5DS-Y-9

2023-03-29 21:55:48

arm力天電子 lpc2148基于DS18B20的溫度控制系統程序代碼之dat=(...

本帖最后由 carey123 于 2014-3-24 14:32 編輯 arm力天電子 lpc2148基于DS18B20的溫度控制系統程序代碼之dat=（j《《7）|（dat》》1）詳解//讀

2014-03-24 14:22:07

為什么LSM9DS1會無法更改FIFO模式？

LSM9DS1無法更改FIFO模式 #fifo＃lsm9ds1 #imu以上來自于谷歌翻譯以下為原文 LSM9DS1 unable to change FIFO mode #fifo #lsm9ds1 #imu

2019-06-13 09:32:45

求基于arm的多DS18B20溫度測量系

本帖最后由 814020145 于 2016-6-22 12:42 編輯要求利用兩個以上DS18B20溫度傳感器，共用數據線，測量溫度， lpc2148，將溫度顯示在LCD上。完全沒有思路能告訴我該怎么入手？

2016-06-21 18:00:04

DS1992,DS1993 pdf datasheet (1

The DS1992/DS1993 memory iButtons (hereafter referred to as DS199_) are rugged read/write data

2008-10-24 13:57:51

DS2155 Monitor Mode Design

Abstract: Application note 400 describes how to connect the Dallas Semiconductor DS2155 single chip

2009-04-20 09:17:26

DS1085/DS1085L EconOscillator頻

Abstract: The DS1085/DS1085L produces a wide range of frequencies on the main oscillator output

2009-04-22 11:02:49

DS1904,pdf,datasheet (RTC iBut

hardware. Data is transferred serially by the 1-Wire® protocol, which requires only a single data lead and a ground return. The DS1

2009-10-03 08:35:25

DS17285, DS17287, DS17485,pdf

The DS17285, DS17485, DS17885, DS17287, DS17487,and DS17887 real-time clocks (RTCs) are designed

2010-05-09 10:27:39

DS17487, DS17885, DS17887,pdf

The DS17285, DS17485, DS17885, DS17287, DS17487,and DS17887 real-time clocks (RTCs) are designed

2010-05-09 10:29:52

1.5/45 Mb/s (DS1/DS3) Line Int

Product Features•Cell based implementation•Selectable mode as DS1 or DS

2010-07-10 10:14:25

DS26522 JTAG Scan Chain Mappin

Abstract: This application note describes the JTAG hardware boundary scan chain for the DS

2009-04-18 11:45:52

793

Additional Pulse Amplitude Set

IntroductionThis application note provides the register settings for the DS2148/DS21348/DS21Q48/DS213Q48 and D

2009-04-20 09:15:14

531

DS31256 and T1/E1 Interface

2155, DS21Q55, DS21Q50 and DS26528 in T1/E1, 2MHz, 4MHz, 8MHz clock mode. The hardware connection and software configuration are given.

2009-04-20 09:26:34

1389

DS2151, DS2152, DS2153, DS2154

Transceivers: DS2151, DS2152, DS2153, DS2154, DS21552, DS21554, DS21352, DS21354 and DS2155. Specifications for selecting the approp

2009-04-20 09:38:44

760

Using DS2148/348 as Repeater

Abstract: Application Note 387 describes the use of the Dallas Semiconductor/Maxim DS2148/DS21348

2009-04-20 09:40:41

837

Converting the DS2151/DS2153 D

Abstract: The DS2151DK and DS2153DK are ordered and shipped for either T1 or E1 operation. However

2009-04-20 10:25:02

559

DS2141A, DS2143, DS2151 and DS

Abstract: This application note describes how the DS2141A, DS2143, DS2151, and DS2153 interface

2009-04-20 10:41:16

744

DS21Q42 vs. DS21Q41B

Abstract: This application note describes the hardware and software differences between the Dallas

2009-04-20 10:47:48

698

DS21Q44 vs. DS21Q43A

Abstract: This application note describes the hardware and software differences between the Dallas

2009-04-20 10:49:25

1304

轉換DS2151/DS2153演示套件-Converting

Abstract: The DS2151DK and DS2153DK are ordered and shipped for either T1 or E1 operation. However

2009-04-29 10:13:03

1037

DS2141A ， DS2143 ， DS2151 ， DS

Abstract: This application note describes how the DS2141A, DS2143, DS2151, and DS2153 interface

2009-04-29 10:18:40

496

DS2141A, DS2143, DS2151 and DS

Abstract: This application note describes how the DS2141A, DS2143, DS2151, and DS2153 interface

2009-04-29 10:21:40

752

DS21Q42 vs. DS21Q41B

Abstract: This application note describes the hardware and software differences between the Dallas

2009-04-29 10:26:37

861

Getting Started with the DS278

The DS2780K Datasheet provides information on connecting the hardware and installing the software on the PC. This Application Note provides a detai

2009-04-30 11:47:19

1302

DS1875 Quick Reference Guide

DS1875 Quick Reference Guide Abstract: The DS1875 burst-mode PON controller with integrated monitoring allows programmi

2009-09-27 11:19:42

1214

DS17285, DS17287, DS17485, DS1

DS17285, DS17287, DS17485, DS17487, DS17885, DS17887實時時鐘應用電路

2010-05-09 10:34:54

870

DS2148、DS21348、DS21Q48、DS21Q348 和 DS21448 的附加脈沖幅度設置

2022-11-18 23:45:41

DS1834DS PMIC - 監控器

電子發燒友網為你提供Maxim(Maxim)DS1834DS相關產品參數、數據手冊，更有DS1834DS的引腳圖、接線圖、封裝手冊、中文資料、英文資料，DS1834DS真值表，DS1834DS管腳等資料，希望可以幫助到廣大的電子工程師們。

2022-12-07 19:55:11

DS1831DS PMIC - 監控器

電子發燒友網為你提供Maxim(Maxim)DS1831DS相關產品參數、數據手冊，更有DS1831DS的引腳圖、接線圖、封裝手冊、中文資料、英文資料，DS1831DS真值表，DS1831DS管腳等資料，希望可以幫助到廣大的電子工程師們。

2022-12-16 22:21:41

DS1831DS+ PMIC - 監控器

電子發燒友網為你提供Maxim(Maxim)DS1831DS+相關產品參數、數據手冊，更有DS1831DS+的引腳圖、接線圖、封裝手冊、中文資料、英文資料，DS1831DS+真值表，DS1831DS+管腳等資料，希望可以幫助到廣大的電子工程師們。

2022-12-26 11:28:03

DS1834DS+ PMIC - 監控器

電子發燒友網為你提供Maxim(Maxim)DS1834DS+相關產品參數、數據手冊，更有DS1834DS+的引腳圖、接線圖、封裝手冊、中文資料、英文資料，DS1834DS+真值表，DS1834DS+管腳等資料，希望可以幫助到廣大的電子工程師們。

2023-01-03 19:29:26